Serving our customers with quality and safety first.
moderately rugged
500 and 651
electrical data all sections; stator input voltage 11.8 v; input current 23 ma max; input power 44 mw; freq 400 hz; zso 444 ohms min to 570 ohms max plus 76 deg min to 81 deg max; zrs 830 ohms min to 940 ohms max plus 16 deg min to 20 deg max; transformation ratio 2.203; phase shift 8 deg; temp rise 10 deg max; null voltage fundamental 25 mv; total 30 mv; electrical error 7 min; friction torque at 25 deg c 0.11 oz ins; zero alignment within 3 min; body dim; pilot dia 0.5 in. max; pilot lg 0.04 in.; flange dia 0.75 in. max; flange thk 0.062 in.; undercut dia 0.692 in.; undercut w 0.062 in.; body dia 0.95 in. max; mounting surface to term end lg 2.955 in. max; o/a lg 3.37 in. max; shaft type rd slotted; shaft dim.; 0.09 in. max dia; 0.325 in. lg; shaft radial play 0.0004 in. and 0.25 lb load; shaft end play 0.0007 in. and 0.5 lb load; shaft runout 0.0010 in.; terminals 6 wire leads; term location rear and side
Two or more synchros on a common mounting or mounted on each other. Do not use this name for single synchros mounted with common synchro accessories such as pulleys, gear reduction units, starting mechanisms.
Packing shall be accomplished in accordance with table c.ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Packing shall be accomplished in accordance with table c.ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping containers in a manner that will ensure safe transportation at the lowest rate to the point of delivery and shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode(s) of transportation to be utilized: (a) postal regulations, (b) department of transportation regulations, (c) civil air regulations, (d) uniform freight classification rules, (e) national motor freight classification rules, (f) american truckers' association rules, (g) other applicable carriers' rules, (h) military air regulations for dangerous materials. consolidation of shipments. all exterior packs of 1.5 cubic feet or less having no single dimension (length, width, height) exceeding 40 inches (and when the total number of such containers in any individual shipment exceeds 25), shall be consolidated, using flat pallets, box pallets, or containers as the consolidating media. dangerous goods shall be prepared for shipment according to applicable department of transportation (dot) regulations and international regulations in effect at time of shipment. shipment by parcel post must comply with postal regulations.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
OPI: Optional Procedure Indicator Code. A one position alpha code that indicates the allowable deviations from the prescribed requirements.
SPI No.: Special packaging instructions number.
LVL A/B/C: Indicates the type of shipping container required for level A, B, or C maximum packing protection.
SPC Mkg: A two position code that identifies the special markings applied to the container, which is part of the total pack to protect the contained item during preservation, packing, storage, transit and removal from the pack.
Indicates there is no data in the hmirs and the nsn is in a fsc not generally suspected of containing hazardous materials.
Precious metal content is unknown
The item does not have a nuclear hardened feature or any other critical feature such as tolerance, fit restriction or application.
HMIC: Hazardous Material Indicator Code. A one position code that identifies a hazardous item.
PMIC: Precious Metal Indicator Code. A one position code which identifies items that have precious metals as part of their content. precious metals are those metals generally considered to be uncommon, highly valuable, and relatively superior in certain properties such as resistance to corrosion and electrical conductivity.
ESD: Electrostatic Discharge. Indicates if an item is susceptible to electrostatic discharge or electromagnetic interference damage. electrostatic discharge damage occurs when an accumulation of static electricity generated by the relative motion or separation of materials is released to another item by direct contact. electromagnetic interference damage occurs when an item comes into proximity with an electrostatic or magnetic field.
ENAC: Enviromental Attribute Code. Identifies items with environmentally preferred characteristics.
CRITL: Criticality Indicator Code. Indicates an item is technically critical by tolerance, fit, application, nuclear hardness properties, or other characteristics.