01-614-0147
Corrosion Preventive Anode
01-614-0162
Strap Hinge
Used on 4940015910265. 0.118" material thickness stamped stainless steel flush hinge tee
01-614-0173
Manual Control Handle
01-614-0190
Retaining Strap
Used on air inlet an exhaust system. strap as
01-614-0230
Mounting Bracket
01-614-0245
Snap Hook
Strap, assy fixed
01-614-0263
Angle Bracket
Used on 5895-01-608-7431. 2nd leg has 4 holes. 2 are 0.190 diameter angle
01-614-0302
Mounting Bracket
01-614-0304
Mounting Bracket
01-614-0305
Butt Hinge
Used on V-22.
01-614-0332
Bail Handle
Used on calibration. handle, front
01-614-0340
Rim Latch
Pressure relief latches
01-614-0352
Bumper
4.250" overall length 12.00" overall width dock, bumper item epdm/sbr rubber surface guards with 0.1875 inch rectangular
01-614-0363
Mounting Plate
Used on 2355-01-539-3639.
01-614-0393
Mounting Bracket
01-614-0396
Access Cover
Main frame modification
01-614-0414
Bow Handle
Used on mrap rg-33. driver side six handle extension
01-614-0417
Bow Handle
Used on mrap rg-33.
01-614-0418
Roller Holder
Used on mrap rg-33. 2.63" overall length 2.63" overall width roller holder bracket weldment
01-614-0420
Extension Stand And Roller Tube
Used on mrap rg-33. 16.190" overall length 1.50" overall width rear tube extention hole dimensions critical
01-614-0424
Catch Strike
Used on mrap rg-33. 8.989" overall length 2.287" overall width
01-614-0426
Catch Strike
Used on mrap rg-33. door catch 2
01-614-0427
Roller Holder
Used on mrap rg-33.
01-614-0436
Mounting Bracket
01-614-0438
Double Angle Bracket
01-614-0442
Double Angle Bracket
01-614-0451
Bumper
Used on mrap rg-33. 1.50" hole diameter
01-614-0468
Mounting Bracket
01-614-0503
Butt Hinge
Used on mrap rg-33. hinge assembly wit hspring
01-614-0528
Angle Bracket
Used on mrap rg-33. driver 3 mounting holea 1.50 x 0.42" angle
01-614-0538
Roller Holder
Used on mrap rg-33. long roller bracket assembly
01-614-0575
Angle Bracket
01-614-0598
Dust And Moisture Seal Boot
01-614-0627
Pipe Hanger
Used on 2330-01-303-8832. split-ring clamping hanger dimensions: length: 1.750; height: 1.125 zinc surface treated split ring
01-614-0675
Access Cover
Used on improved target acquistion system (itas). 2.0" inside diameter 4.0" outside diameter cap, mount assembly item has 10.0 inch wire rope attached to cap; has square strip of velcroon top of cap;
01-614-0708
Mounting Plate
Used on 3930-01-599-9978. pad assembly
01-614-0744
Angle Bracket
01-614-0825
Protective Nut And Bolt Hea Cap
Used on 4940-01-591-0265. cap, nut washer for unthreaded 5/8 inch shaft zinc surface treated
01-614-0830
Cover Retainer
01-614-0831
Cover Retainer
01-614-0832
Mounting Bracket
01-614-0910
Electronic Equipmen Hardware Kit
Pole mounting kit for pathfinder proxrt gps receiver
01-614-0940
Bow Handle
Used on nsn 2330-01-303-8832. 2a thread class right-hand 1.000" thread length 21.500" overall length 20 thread quantity per inch retention bar must be certified free of cadmium or hexavalent chromium round unc thread series
01-614-0989
Protective Dust And Moisture Cap
01-614-1171
Mounting Bracket
Used on 4940-01-591-0265. 6.630" overall length 2.000" overall width welder mount bracket
01-614-1228
Multiple Angle Bracket
Used on 2330-01-303-8832. 4.57" overall length 6.94" overall width 0.0598" material thickness assembly, wire guard bracket has 4 mounting slots. the slot dimensions are 0.96" long by 0.311" wide. on one side the bracket wall has a thru hole with a 0.75 inch diameter that is 2.87" from the end. plastic polyamide surface treated quadruple angle
01-614-1232
Loop Clamp
Used on 4940-01-591-0265. 0.5625" overall width 0.3125" material thickness clamping u-bolt zinc surface treated two piece
