01-204-2706
Snap Fixed Gage
3.500" overall length final protective finish: black oxide per mil-c-13924 class 1
01-205-6476
Plug Plain Cylindrical Gage
Attached streamer reads "remove before flight"; to determine adequate engagement of hook under latch rollers of canopy mechanical release system, t-46 acft
01-206-5300
Comparator Electronic Gage
Gear involute tester
01-209-0036
Ring Master Setting Gage
Gage set, rings, master setting; for calibration of bore gages, consists of the following sizes: 0.275, 0.350, 0.425, 0.500, 0.600, 0.700, 0.800, 0.900, 1.000, 1.200, 1.400, 1.600, 1.800, 2.000, 2.400, 2.8.00, 3.200, 3.600, 4.000, 4.400, 4.800, 5.000, 6.000, and 7.000"; class of the master setting ring set is x
01-209-0037
Ring Master Setting Gage
Gage set, rings, master setting; for calibration of bore gages
01-209-1427
Comparator Electronic Gage
01-210-3319
Disk Master Setting Gage
01-210-5092
Disk Master Setting Gage
01-210-5093
Disk Master Setting Gage
01-212-2094
Profile Gage
Used on c130b acft. gage, inspection
01-212-5127
Plug Plain Cylindrical Gage Set
Gage set, plug; consists of one set of 25 w/ gage of 0.2495 in. w/12 sizes in .0001 steps up from size
01-212-5320
Surface Plate
01-212-8484
Plug Plain Cylindrical Gage
01-212-9197
Surface Plate
01-212-9225
Plug Plain Cylindrical Gage
01-212-9229
Profile Gage
Gage, chord, rotor
01-213-2729
Comparator Electronic Gage
01-213-2730
Profile Gage
Used on f-15 acft. gage, linear, variable ramp; stainless steel, passivated; 19 in. long x 3 in. dia.; alumunim, plastic container; used to measure the air inlet variable 3rd ramp setting
01-213-3205
Surface Plate
01-213-3206
Surface Plate
01-213-3207
Surface Plate
01-213-3208
Surface Plate
01-214-3427
Precision Master Level
Used on aah/tads (target acquisition designation sight), other missile related materiel.
01-214-4544
Comparator Electronic Gage
01-214-9833
Profile Gage
Used on f100 engine. gage; to measure inlet case variable vanes for trailing edge flap play
01-215-2445
Comparator Electronic Gage
Measuring machine, c
01-215-3631
Surface Plate
Stand, surface plate; used for 36.0 inch by 48.0 inch plates
01-215-3638
Profile Gage
Gage, setting; u/o M61A1 20mm gun nose guide
01-215-3763
Surface Plate
01-215-6719
Comparator Air Plu Gaging Member
01-215-6847
Surface Plate
Stand, surface plate; to support surface plate 5220-00-277-1733
01-215-6848
Comparator Electronic Gage
Amplifier, digital reading; ambient temp 32 to 122 deg f; incl rechargeable battery p/n 405-492; height 8.25 in.; width 7.25 in.; depth 7.50 in.
01-215-6849
Profile Gage
Used on kc135r acft. gage, rotor blades; to determine trailing edge of rotor blades
01-216-0602
Profile Gage
Used on aircraft propeller series d2af34c; to 3m3-6-4; to name: gage, stud standoff. gage, stud standoff; used to check height of installed studs
01-216-6049
Profile Gage
Gage, latch weight; used to test position of latch weights on o-2a propeller
01-217-3155
Profile Gage
Gage; gear box support link assy for F100-3; consists of 1 storage container, 1 gage, 1 flat pt. soc. set scr., a 1 handle; is 5.75 in. lg, 0.75 in. max dia
01-218-0846
Comparator Electronic Gage
01-218-9065
Profile Gage
Used on f100-pw-100 eng.. gage, slot check; item is 1.5 in. lg, 1.0 in. high
01-218-9066
Profile Gage
Used on f100 pw100 200 engine. gage, engine stator
01-218-9185
Comparator Air Gage
Item must comply with requirements of defense supply center columbus production standard no. L09027
01-218-9371
Ring Master Setting Gage
01-218-9372
Ring Master Setting Gage
01-219-9783
Comparator Electronic Gage
Xmeasuring machine, computer controlled; consists of 1 desktop computer w/twin 5 1/4 in. integral flexible disk, 1 memory module 256 k, 1 dma board, 1 ram based hpl 2.1.1 16 bit gpid interface, 1 interface, 1 printer w/046 option 200 cps w/136 characters per line, 1 paper catcher, 1 disk drive w/004 option 4.6 mybte cap., 3 1/2 microfloppy, 1 cable/one meter, and 1 pack of 10 flexible disks; the machine, air dryer
01-220-3846
Comparator Electronic Gage
Measuring machine; rotor erom is a measuring machine in which the operator loads
01-220-4423
Disk Master Setting Gage
Used on turbofan engine. lgage, turbine disk; used to determine the growth of the third stage turbine disk to see if its within specified dimensions for reinstallation; material steel w/supporting details; size 8 in. lg, 5 in. wide, 3 in. high
