01-247-4754
Final Drive Assemb Alignment Pin
01-247-6128
Piston Ring Compressor
01-247-6131
Mechanical Puller
01-247-6388
Mechanical Finger
Used during installation of the reentry system deployment module lateral support group pads; tool interfaces w/retention release system turnbuckle assy, the tool secures the turnbuckle while the cable is being tensioned; consists of 2 open end wrenching elements joined together by a common support rod; e/i LGM118a peacekeeper
01-247-6389
Bearing And Bushing Inserter
3.290" overall length
01-247-6390
Bearing And Bushing Inserter
5.000" overall length
01-247-6391
Bearing And Bushing Inserter
5.000" overall length
01-247-7272
Box And Open End Combinat Wrench
5.000" overall length
01-247-8863
Seal Inserter
Used to compress the "t" seal with back-ups in order to install the balance rod inside of the piston; tool is made of aluminum alloy, weighs approximately 0.70 lbs., and measures 2.25 in. dia. x 2 in. long
01-247-8877
Bushing Driver Set
01-248-1797
Socket Wrench
Used on 200 and 600 series heads.
01-248-1808
Mechanical Puller Adapter
Component of kent-moore no. J35178 camshaft bearing puller nsn 5120-01-206-3818
01-248-1809
Mechanical Puller Adapter
Component of kent-moore no. J35178 camshaft bearing puller nsn 5120-01-206-3818
01-248-1810
Mechanical Puller Adapter
Component of kent-moore no. J35178 camshaft bearing puller nsn 5120-01-206-3818
01-248-2363
Drive Pin Punch
Used for the insertion of two dowel pins into the gyro case; consists of drill rod stock
01-248-2663
Mechanical Finger
Matl stainless steel, 6.0 in. lg, 1.5 in. w, 5/8 in. thk, and is used to retain drive shaft during removal/assy of gearbox, F112-wr-100 engine
01-248-2686
Mechanical Puller
Matl carbon steel, black oxide finish, height 9.0 in., dia 9.5 in., reach 8.0 in., used to remove fuel slinger bearing removal
01-248-2687
Mechanical Puller
Matl carbon steel, black oxide finish, jaws flame hardened, height 3.5 in., dia 3-3/8 in., reach 1.5 in.; used to remove no.5 small dia seal support from 2nd stage turbine nozzle nozzle housing bearing removal
01-248-2925
Wrenching Tube Fitting Socket
78.0mm overall length chromium surface treated open side
01-248-5409
Electrical Inserter And Remover
01-248-5410
Electrical Inserter And Remover
Material will be in accordance with ships part control center activity hx quality control, manufacturing
01-248-5411
Electrical Inserter And Remover
01-248-6370
Bearing Inserter And Remover Set
Used on b-1b aircraft.
01-248-6735
Terminal Hand Crimping Tool
Used to install all "d" connectors except 50 position; tool is used with the frame installation tool to crimp connector onto ribbon cables
01-248-6736
Electrical Contact Remover
01-248-6737
Preformed Packing Inserter
1.820" overall length e/i F108 engine
01-248-6738
Preformed Packing Inserter
1.700" overall length e/i F108 engine
01-248-6739
Pin Inserter
E/i F108 engine
01-248-7684
Spanner Wrench
01-248-7737
Bearing And Bushing Inserter
6.000" overall length
01-248-9191
Adjustable Wrench
Used on engine model tf30,turbofan. 5.000" overall length
01-249-0380
Melting Electric Pot
Aluminum; 600 watts; 5 in. inside dia, 3-1/2 in. depth; 7 in. outside dia, 6-1/2 in. depth; 60 - 250 degrees f heating range
01-249-0756
Terminal Hand Crimping Tool
01-249-2289
Torque Wrench Adapter
0.250" outside diameter o/a lg 6.5 in.; e/i F107 eng socket to socket
01-249-2293
Box Wrench Set
A pin is welded thru 5/16 box end to provide handle; black oxide fin o/a; e/i F108 eng
01-249-2458
Offset Screwdriver
4.750" overall length e/i F100 engine opposite offset, opposite ends, each off set tipped
01-249-2459
Pliers
Used to prevent damage to the tube assembly while tightening, torquing or loosening coupling sleeve nut; e/i F107 engine
01-249-2860
Screw Hand Jack
Used on patriot, surface to air missiles.
01-249-6358
Socket Head Screw Key
4.594" overall length l-handle
01-249-7127
Spring Inserter And Remover
10.500" overall length
01-249-7128
Spring Inserter And Remover
6.000" overall length
01-249-9837
Torque Wrench Adapter
Used on detroit diesel series 149 engines.
01-249-9912
Socket Head Screw Key Set
Used on jensen no. 281b100 torque screwdriver. contains 8 hex key blades
01-250-0889
Electronic Equipm Alignment Tool
01-250-0890
Electronic Equipm Alignment Tool
01-250-4930
Terminal Hand Crimping Tool
Tool only, dies do not come with tool, die sets 312253-1 for rg-402_AND312253-2 for rg-405 cable
01-250-7162
Spanner Wrench
Used on f-16 acft.
01-250-7484
Bearing And Inserter And Remover
E/i b-52g/cm
01-250-7598
Socket Wrench Socket
01-250-8066
Socke Screwdriver Attachment Set
Chromium sockets, zinc chromate bits
