01-186-3128
Bearing And Bushing Remover
Used on owatonna tool co. no. y-850 tool set; family of hemtt vehicles (heavy expanded mobility tactical trucks).
01-186-3978
Spanner Wrench
01-186-7119
Retaining Ring Installation Tool
Used on uh-60, rotary wing aircraft.
01-186-7839
Torque Wrench Adapter
01-186-7840
Torque Wrench Adapter
01-186-9912
Spanner Wrench
6.375" overall length oxide surface treated adjustable face pin
01-187-0384
Seal Inserter
Used on cummins series v-903 engines. 5.000" overall length
01-187-0784
Torque Wrench Adapter
Used on sturtevant-richmont type ccm and ltc torque wrenches. open end
01-187-1786
Socket Wrench Set
01-187-1787
Tube Hand Bender
For bending tubing up to 180 deg
01-187-3348
Mechanical Puller
Bearing removal
01-187-3349
Mechanical Puller
01-187-3350
Bearing And Bushing Inserter
10.000" overall length
01-187-3607
Seal Inserter
1.500" overall length
01-187-3628
Mechanical Puller
Used on nsn 2320-01-123-1602 light armored vehicle. consists of snap-on tools no. cg-250-10 jaw (3) , cg-270-1a pressure screw, cg-273-2 yoke, cg-273-5 plate, cg-270-6 spring
01-187-3659
Bearing And Bushing Inserter
Used on 2320-01-146-7187. 3.750" overall length
01-187-3660
Bearing And Bushing Remover
01-187-5476
Mechanical Puller
C/o cap, cover, body, base, ring; to remove rear seal sleeve
01-187-5486
Mechanical Puller
Fixture shaft removal item is used during depot level maintenance to remove the axial assy from the l.p.shaft; will be used with the swing table
01-187-5487
Seal Inserter
4.000" overall length
01-187-5488
Leveling-support Jack
Used on levels van for an/tpq-43. pthis is a mechanical screw jack with extendable screw of more than onefoot; support end is free to swivel 360degrees
01-187-5711
Mechanical Puller
Also includes a steel base w/a centrally located pilot stud, used to remove the front seal of the cruise missile engine, F107 gear
01-187-5712
Mechanical Puller
Gear
01-187-5713
Mechanical Puller
Slide hammer, gear
01-187-5714
Mechanical Puller
Gear
01-187-5715
Mechanical Puller
Gear
01-187-5716
Mechanical Puller
Used during depot level maintenance of the air vehicle engine to disassemble the axial assembly; item is 2 part consisting of square metal base 6 inch square with a centered shaft 4" long to accept axial rotor group
01-187-5717
Mechanical Puller
Used during depot level maintenance of the air vehicle engine to remove the spinner; it is installed with the puller fingers engaged in the 3 holes in the spinner housing; the threaded shaft is turned down onto the l.p. shaft
01-187-5718
Mechanical Puller
Item is used during depot level maintenance of the air vehicle engine to remove the 2nd stage turbine; it is cylindrical in shape, 6.5" long by 3" dia, with a sleeved section which grips the 2nd stage turbine, the nylon rod is threaded into the outer sleeve, bears onto the l.p. shaft
01-187-5719
Mechanical Puller
Item is used for depot level maintenance to remove the no. 5 carbon seal support; the puller is cylindrical
01-187-5720
Mechanical Puller
Item is used during depot level maintenance of the air vehicle engine to remove the no. 3 bearing support; cosists of an aluminum ring 5" dia, with a top support member with a threaded shaft bearing, clutch pilot, with head guide
01-187-5721
Mechanical Puller
Yitem is used for depot level maintenance of the air vehicle engine to remove the no. 5 large carbon seal; bearing, clutch pilot, with head guide
01-187-5722
Mechanical Puller
Gear
01-187-5723
Bearing And Bushing Remover
01-187-6718
Offset Screwdriver
01-187-8056
Box Wrench
5.350" overall length 0.706" outside diameter u/o hi-shear HST22ht pin
01-187-8185
Seal Inserter
01-187-8400
Mechanical Puller
Steel; 2 puller jaws engage slots at lower end of bearing plate; outer legs on gearbox housing; force applied to center puller nut to remove duplex bearing plate from main gearbox housing
01-187-8401
Mechanical Puller
3 legs atchd to puller yoke internally engage 3 holes of seal housing p/n 3083502-1; threaded shaft thru yoke engages lpt shaft p/n 3083531-1 with swivel pad
01-187-8402
Mechanical Puller
2 legs atchd to puller yoke externally engage aft lip of retainer p/n 3083543-1; threaded shaft thru yoke engages lpt shaft with swivel pad; force onpuller shaft removes retainer
01-187-8403
Mechanical Puller
3 legs internally engage inner lip of plate p/n 3083006-1, secured by half turn screws; threaded puller shaft engages disk p/n 3083013-1 with swivel pad; force on puller shaft removes plate
01-187-8404
Seal Inserter
3.000" overall length
01-187-8405
Seal Inserter
6.000" overall length
01-187-8406
Seal Inserter
6.000" overall length
01-187-8432
Socket Wrench Socket Set
01-187-8433
Socket Wrench Set
01-187-8434
Socke Screwdriver Attachment Set
Chromium socket, oxide bit
01-187-8441
Drive Pin Punch
5.500" overall length shank shape may also be round, square or octagonal
