National stock numbers that we have updated recently with new information.
test package radar antenna used in conjunction with an/gsm-228 antenna test station for the f-15 series aircraft
test package ultra high freq used in conjunction with an/gsm-228 antenna test station for the f-15 series aircraft to 33d7-50-1-101
low frequency preselector consists of 18 capacitors filter amplifier monitor amplifier rf amplifier speaker 8 transistors
length 1.126 thread length 0.5 nut thread steel corrosion resisting material
2 packing-preformed no. ms28775-017 2 packing-preformed no. ms28775-137 1 packing-preformed no. ms28775-145 1 packing-preformed no. ms28775-148 2 packing-preformed no. ms28775-234 1 packing-preformed no. ms28775-237 1 packing-preformed no. ms28775-3
aluminum alloy qq-a-225/9 no. 7075 condition t7351 anodized finish 13.1 in. o/a length 2.03 in. o/a diameter machined surfaces 32 and 125 microinch finish as noted
steel ams6381 no. 4140 0.63 in. o/a length 2.955 in. minimum to 2.965 in. maximum o/a diameter 2.584 in. minimum to 2.589 in. maximum bore diameter 4 metering holes 0.124 in. minimum to 0.127 in. maximum diameter machined surfaces 125 microinch finis
aluminum alloy qq-a-200/3 no. 2024 condition t3511 1.74 in. o/a length 2.996 in. minimum 2.998 in. maximum o/a diameter 2.438-16n-3b thd 1.1 in. length machined surfaces 32 and 125 microinch finish as noted 0.1 in. diameter holes 2 places
steel mil-s-6758 condition f4 no. 4130 one end nickel plate finish balance chrome plate finish 5.25 in. o/a length 0.875 in. o/a diameter major body machined surface 16 microinch finish heat treat 160000 to180000 psi
cres ams 5643 no. 17-4ph passivated finish 4.637 in. o/a length 1.5 in. o/a width 1.5 in. o/a height as noted machined surfaces 16 32 and 100 microinch finish 0.625 in. minimum 0.626 in. maximum diameter bore counter bored 0.995 in. minimum 1.005 in
a2 packing no. ms28775-012 10 packing no. ms28775-019 2 packing no. ms28775-122 2 seal-slipper no. s-50-013n 9 seal-slipper no. s-50-020n 1 t-seal no.s-52-1 mfr code 99643 for all part nos.listed
inside diameter 0.127 minimum and 0.129 maximum nominal thread size 0.112 screw hole
inside diameter 0.252 minimum and 0.254 maximum depth 0.562 width 0.562 thickness 0.719
t.o. 16a1-13-18-3 diameter 5.75 in. ballscrew diameter 1.1 in. length 58.957 in. travel 49 in.
nominal overall length 8 nominal overall width 4 used to align the overcenter link of the rudder pedal leg-length adjustment mechanism relative to other linkage
length 2.2 taper included angle 5 degrees steel material inside diameter 1.25
pitch diameter 0.702 minimum and 0.703 maximum pressure angle 20 degrees aluminum material nominal overall length 0.29
pitch diameter 0.795 minimum and 0.796 maximum nominal overall length 0.29 aluminum material pressure angle 20 degrees