01-499-0537
Metal Plate
Used on bradley; 2350-01-432-1526. fthere is a rectangular cutout in the center of this plate, 4.500X4.110 with corners rounded to radius of 0.500; there are 8 holes 0.164-32unc-2b paint surface treated
01-499-0634
Metal Sheet
Dimensions - 071X36X72
01-499-0636
Metal Sheet
Dimensions- 032X36X72
01-501-1611
Laminated Shim Stock
Used on mv-22 aircraft (v-22 lrip 1 e-nsn isil). shim, peelable, laminated, fiberglass, square these shims are intended for use in graphite composite structure
01-501-1649
Laminated Shim Stock
Used on mv-22 aircraft (v-22 lrip 1 e-nsn isil). shim, peelable, laminated, fiberglass, square these shims are intended for use in graphite composite structure
01-501-1693
Laminated Shim Stock
Used on mv-22 aircraft (v-22 lrip 1 e-nsn isil). shim, peelable, laminated, fiberglass, square these shims are intended for use in graphite composite structure
01-501-1706
Laminated Shim Stock
Used on mv-22 aircraft (v-22 lrip 1 e-nsn isil). shim, peelable, laminated, fiberglass, square these shims are intended for use in graphite composite structure
01-501-1742
Metal Strip
Used on v-22 aircraft. copper strip, aircra e-nsn isil
01-502-3294
Metal Plate
Used on fighting vehicle systems,bradley (bfvs). floor plate, driver's station material thick is 0.125 inch, refer to drawing for specific dims
01-502-5012
Metal Plate
Used on transmitter.
01-503-7445
Armor Plate
Armor plate, left side, upper center with long sides of plate vertical, left side is cut from point 21.11" from left top at 50 degree angle toward top of right edge
01-505-1473
Floor Metal Plate
01-505-1478
Floor Metal Plate
01-506-0395
Floor Metal Plate
01-507-1387
Metal Strip
Used on 2410-01-253-2118. guard strip lh
01-507-1395
Metal Plate
Used on 2410012532118. plate
01-507-2404
Metal Plate
Used on 2410-01-253-2118.
01-507-9320
Metal Sheet
Used on c5 acft.
01-507-9321
Metal Sheet
Used on c5 acft.
01-507-9323
Metal Sheet
Used on c5 acft.
01-509-7584
Floor Metal Plate
01-509-7591
Floor Metal Plate
01-509-9610
Metal Sheet
Used on reducer, lcl heat exchangers; asds. cover, inner left/short side is cutout from point 3.39 in. from top on a slant to point 10.96 down
01-509-9620
Metal Sheet
Used on reducer, lcl heat exchangers; asds. cover, outer left/short side is cutout from point 3.39 in. from top on a slant to point 10.96 down
01-509-9630
Metal Sheet
Used on reducer, lcl heat exchangers; asds. cover, inner left/short side is cutout from point 1.53 in. from top at 55 deg. to point 10.875 down & 12.75 from left edge, then straight down to bottom edge; right side has similar cutout from 1.53 down to point 10.875 down & 12.75 from right edge, then straight to bottom; cover bends up at 4.0 deg. angle, 1.56 in. from top edge
01-509-9643
Metal Sheet
Used on reducer, lcl heat exchangers; asds. cover, outer left/short side is cutout from point 1.53 in. from top at 55 deg. to point 10.875 down & 12.75 from left edge, then straight down to bottom edge; right side has similar cutout from 1.53 down to point 10.875 down & 12.75 from right edge, then straight to bottom; cover bends up at 4.0 deg. angle, 1.56 in. from top edge
