01-082-8844
Profile Gage
Used on j75 engine. gage, flow; area, 1st stage turbine nozzle vane, matl stl, size 6.000 in. by 6.000 in. by 12.000 in.
01-083-5426
Angle Solid Plate
Used on 2350-01-031-0586;howitzer,medium s-p.
01-084-1230
Ring Taper Gage
Steel, corrosion resistant matl; flat gage 0.060 in. thk; 4.728 in. o/a length; 0.680 in. w; 0.114 in. lg nipple protruding at each end of gage; gage to be used in top ring groove, piston no. 11683943 series
01-084-6131
Comparator Air Plu Gaging Member
Used on f-16 acft. air spindle, gage
01-085-1388
Comparator Air Plu Gaging Member
Used on f-16 acft. air spindle, gage
01-085-3184
Precision Master Level
01-085-6628
Profile Gage
Gage assembly; matl corrosion resistant steel; size 16.000 by 14.000 by 6.000 in.; consistof a rectangular base on which is mounted a clamping device, a spring loaded pilot, a plunger,
01-085-6723
Plug Thread Gage
Right-hand
01-085-7530
Comparator Electronic Gage
Used on t56 engine. calculator, engine performance; 9.000 in. long, 2.500 in. high, slide rule type calculator, case material transparent vinylite-slide opaque vinylite, slides shall move only under pressure, calculator gives readings of installation effect, performance, indicator torque, ambient temp., pressure-altitude, altimeter reading at 29.92 in.hg, ambient temp., horsepower-torque, above description is face of calculator; reverse as follows-gives turbine inlet temp., ambient temp., turbine inlet temp., installation effect, pressure-altitutde, altimeter reading at 29.92 in. hg, performance
01-085-8516
Plug Thread Gaging Member
Right-hand annular
01-086-0212
Profile Gage
Used on f100-pw-100. gage, setting; 8.000 in. dia., 10.500 in. high, gage is attached to hi-shear power unit
01-086-1255
Profile Gage
Used on tf 41 engine. gage assembly, cooling air hules; consists of 1 gage, matl sae 01 steel hdn rc C55-60; 2.250 in. long; 2 pins, matl ams 2485, 0.125 in. by 0.500 in. long; 1 handle, matl alum. 6061-16, 2.500 in. long, gage is an fgge break, 0.035 in.-0.065 in. rail l.p. turbine shaft cooling air rules
01-086-1423
Plug Thread Gage
Right-hand
01-086-1424
Plug Thread Gage
Right-hand
01-086-8020
Comparator Electronic Gage
Used on j33 engine. gage, eddy current; gage is for eddy current standard, 6th serration J33 turbine wheel
01-086-8886
Plug Thread Gage
Right-hand
01-087-3423
Profile Gage
Used on f100-pw-100 and 200. comparator, chart; for 2nd stage turbine retainer plate, matl is mylar, size 18.000 in. square, approx.
01-087-5045
Profile Gage
Used on upt/avrs t-378. gage, tension; tension of up to 2000 gram w/an accuracy of 1 gram
01-087-6673
Profile Gage
Used on tf-41 engine. gage, plate assembly; retaining h.p. turbine blade stage 1 consisting 1 base, 2.38 in. w, 1.50 in. l, ; 1 support, matl weldment, l shape, 1.56 in. w, 2.00 in. lg.; 2 screw soc hd cap, 190-29 by 62 lg.; 1 screw, soc hd cap 164-32 by 38 lg.; 1 dial indicator-miniature model A3w with adj. back, mfr 21938 p/n bk-45; 1 pin, 0.093 in. dia. by 0.88 in. lg.; 1 gage pin, matl sae 02 hdn-rc 48-52; 2 pin locating, matl sae 02 hdn-rc 48-52, 0.62 in. lg., 0.125 in. thk.; 1 master, matl sae 4340 hdn rc 48-54, 2.00 in.lg., 1.940 in. high; 1 spring mfr lee spring, p/n lc-0220-7
01-087-8968
Profile Gage
Gage, pla piston stop, consisting of a machined steel gaging block with knurled steel operating handle, size 1.00 in. wide, 5.00 in.long, 1.00 in. high; used on F100-pw-100
01-087-8969
Profile Gage
Used on f100-pw-100. gage, preset; retainer assy consisting of a machined steel bar of gaging thickness
01-088-0472
Crimping Tool Gage
Matl, type 1 tool steel; surface finish black oxide huck spec 409; rockwell hardness C55-C60; width 0.750 in.; go-gap end 0.359 in.; no go-gap end 0.353 in.
01-088-0971
Profile Gage
Used on f100-pw-100. cgage, loading lever; item is weight-loading lever consisting of a circular machined corrosion resistant steel rod section
01-088-2221
Crimping Tool Gage
Matl-type 01 tool steel; surface finish black oxide huck spec 409; rockwell hardness C55-C60; width 0.625 in.; go-gap end 0.275 in.; no go-gap end 0.269 in.
01-088-2222
Crimping Tool Gage
Matl-type 01 tool steel; surface finish black oxide huck spec 409; rockwell hardness C55-C60; width 0.625 in.; go-gap end 0.267 in.; no go-gap end 0.261 in.
01-088-2223
Crimping Tool Gage
Matl-type 01 tool steel; surface finish black oxide huck spec 409; rockwell hardness C55-C60; width 0.750 in.; go-gap end 0.363 in.; no go-gap end 0.357 in.
01-089-0952
Surface Plate
Used on f-16 support equipment. stand, surface plate; stand is 36.000 in. by 72.000 in.
01-089-6195
Profile Gage
Used on f100 engine. gage, inspection
01-089-6196
Profile Gage
Used on f100 engine. gage, compressor disk
01-089-6197
Profile Gage
Used on f100 engine. gage, compressor disk
01-090-5694
Profile Gage
Used on j85-21 engine. gage, compressor stator; compressor stator w/a dial indicator, matl steel, finish black oxide, envelope size 14 in. by 22 in. by 10 in., weight 70 lbs.
01-090-8806
Crimping Tool Gage
Matl-type 01 tool steel; surface finish black oxide huck spec 409; rockwell hardness C55-C60; width 0.500 in.; go-gap end 0.237 in.; no go-gap end 0.232 in.
01-091-0342
Profile Gage
Used on mfr 99193 p/n 3505230-1-1;c130 engine. gage, bearing
01-091-2136
Profile Gage
Used on tf-33 engine. gage, broaching; item is a gage assy w/handle & box, gage assy matl is aisi-m-2 hdn rc c 59-63; 0.75 in. lg., 1.00in. high, brazed construction black oxide per ams 2485 after brazing
01-091-2137
Profile Gage
Used on tf-33 engine. gage, broaching; gage assy w/a handle
01-091-2935
Profile Gage
Used on tf-33 engine. egage; consists of 1 base, 2 dowel pins, 1 flush pin, 1 dowel pin, 1 box; base matl is steel aisi 01 hdn rc c 59-63, 1.00 in. lg., 1.00 in. high, 0.125 in. porm 0.001 dia. 0.500 in. deep-construction hole, 0.3133 in. minus 0.000 in. plus 0.0003 in. dia., 0.094 dia. to depth shown 0.0620 in. minus 0.0000 in. plus 0.0004 in. dia. thru 2 holes; dowel pins, matl sst mfr 96906 p/n MS16555-606, 0.062 in. dia. by 0.500 in.; 1 flush pin, matl steel aisi 01 hdn rc c 59-63, 0.95 in. lg. approx., 0.3127 in. pormo 0.0001 in. dia., 0.047 in. by 45 degrees chamfer; 1 dowell pin, matl sst, mfr 96906 p/n MS16555-629, 0.125 in. dia. by 0.750 in., 1 box, matl plastic mfr 03663, p/n MP340-H2-RC1; gage is 1st stage turbine disk rivet slot spotface
01-091-2936
Plug Countersink Gage
Used on tf-33 engine. gage, countersink; item is a gage countersink, 1st stage turbine disk rivet slot consisting of one base, one dowel pin, one gage pin, one container; base matl is aisi 01 hon rc c 59-63, 0.344 in. minus 0.005 in. plus 0.000 in. dia., 2.000 in. high, dowel pin, 0.125 in. dia. by 0.500 in., gage pin matl steel aisi 01 hdn rc c 59-63; container matl polyethylene mfr 11134 p/n f-17872
01-091-4133
Profile Gage
Used on tf-33 engine. 8gage; 1st stage turbine disk rivet slot consisting of 1 base, 2 flush pins, 1 dowel pin, 1 box; base matl is steel aisi 01 hdn rc c 59-63, 1.250 in. reference high, 1.00 in. lg., 0.125 in. porm 0.001 in. dia. 0.500 in. deep-construction hole, 0.3133 in. minus 0.0000 in. plus 0.0003 in. dia. thru; dowel pin matl sst mfr 96906 p/n MS16555-629, 0.125 in. dia. by 0.750 in.; 1 flush pin matl steel aisi 01 hdn rc c 59-63, 1.22 in. approx. lg., 0.3127 in. dia. porm 0.0001 in.; 1 box matl plastic mfr 03663 p/n MP3402h-RC1
01-091-8943
Angle Solid Plate
01-093-0437
Coating Thickness Gage
Analyzer, surface finish; for cirular tracing; stylus tip radius 500 porm 100 micro-inches; stylus force 2.5 grams; tracer head shall be sufficient for rugged heavy duty type tracing work; movement of tracer-is provided w/or incorporate a motor driven device, the device shall provide adj. to vary the length of traverse, length shall be used as follows-measure the roughness of i.d.
01-094-4673
Precision Master Level
01-095-8029
Profile Gage
Used on gtc85-70a and 71a eng.. gage, gear setup; material tool steel, 1.65 in. by 5.00 in. by 5.00 in., weight 3 pounds
01-096-2579
Profile Gage
Used on f-16 acft age;t.o. 35d30-4-11-1. nfixture, tolerance check; stainless steel, passivated; 18 x 18 x 12; wght 20 lbs; storage case; used after a loader stoppage of the interface unit, checks for reason for stoppage; fsc appl data - ammunition handling system
01-096-2580
Profile Gage
Fixture, conveyor element; matl steel, 9X9X6, 3 lbs.; used to check for worn/damaged elements the replenisher (30 mm) ; end item f-16 acft age; t.o. 35D30-4-11-1 ammunition replenisher
01-098-0923
Profile Gage
Used on f100 turbofan eng.. gage standard, probe calibration; consists of 0.80 in. high, 1.80 in. wide, 4.00 in. long, matl titanium
01-098-9515
Profile Gage
Gage, go no-go; gage is for inspecting leadiing edge, fan blade; cubage 0.500 in. by 1.500 in. by 13.000 in; the form is cast with the allowable deformation of 0.125 in. from master blade; used on TF34-ge-100eng
01-099-2769
Ring Plain Gage
Used on t56-a-15 turboprop engine-t56-a-7a/b,9c/d model engines. gage, ring; special gage ring for compressor front bearing-hyatt
01-099-5029
Profile Gage
Used on tf-39 engine. ggage, radial play; to check 1st
01-099-7804
Plug Plain Cylindrical Gage