01-552-6515
Plug Plain Cylindrical Gage
01-552-7174
Plug Plain Cylindrical Gage
01-552-7175
Plug Plain Cylindrical Gage
01-552-7178
Plug Plain Cylindrical Gage
01-552-7179
Plug Plain Cylindrical Gage
Used on sikorsky s-70/h-60 seahawk helicopter. starting hole gage, second oversize dia., 1.4170/1.4190", fan-555, rh side aft spar lugs, folding stabilator, location 1, sub-location 0
01-552-7180
Plug Plain Cylindrical Gage
01-552-7183
Plug Plain Cylindrical Gage
01-552-7184
Plug Plain Cylindrical Gage
01-553-1491
Ring Plain Gage
01-553-3329
Profile Gage
Used on f100-pw-100/200/220/220e aircraft engines. 1st stage compressor air seal
01-553-5842
Profile Gage
Used on umbilical cable termination tool kit, an/slq-48.
01-554-2538
Profile Gage
Gage, flange
01-554-4507
Surface Plate
Plate, lever arm
01-554-5474
Headspace Gage
Used on used for sr-25/mk11 weapon.
01-556-0459
Profile Gage
Gap inspection gage; 1/4 in, 3/8 in, 6 mm
01-556-0464
Profile Gage
Gap inspection gage; 1/16 in female nuts
01-558-1129
Comparator Air Gage
Used on aircraft model s70b. inspection gage, rod end bearing
01-559-2626
Crimping Tool Gage
01-559-3510
Inspection Master Setting Gage
Used on turbine shaft coupling. used to set PWA72598 gage to measure the turbine shaft coupling
01-559-3511
Inspection Master Setting Gage
Used on turbine shaft coupling. used to set PWA72585 fixture to accept the turbine shaft
01-559-3703
Plug Thread Gage
Used on 1025-01-445-0991; 155mm lightweight howitzer, medium, towed. right-hand gage, M4X0.7; 5h thread metric coarse
01-559-3719
Plug Thread Gage
Used on 1025-01-445-0991; 155mm lightweight howitzer, medium, towed. right-hand gage, M3X0.05; 5h thread metric coarse
01-559-3758
Plug Thread Gage
Used on 1025-01-445-0991; 155mm lightweight howitzer, medium, towed. right-hand gage 0.112-40, unified coarse
01-559-6841
Profile Gage
Used on 3820-01-435-8025. used to ensure precise hole placement when punching holes in belt; calle v-belt tension gauge
01-560-2726
Angle Solid Plate
Used on pump assembly, water 4320-01-533-6418. manufacturer item name: angle plate
01-560-3419
Firing Pin Protrusion Gage
Bru-44 used on bomb rack for b-2 only; height checker, gage, firing pin protrusion
01-560-4001
Comparator Electronic Gage
Used on reference standard set,physical prop; 6635-01-497-3151.
01-560-6033
Ring Plain Gage
01-560-9460
Crimping Tool Gage
01-561-5204
Crimping Tool Gage
01-561-7996
Plug Countersink Gage
Used to measure the reamed starting hole for a forcemate bushing installation on f-16;
01-561-8008
Plug Countersink Gage
Used to measure the reamed starting hole for a forcemate bushing installation on the f-16;
01-561-8015
Plug Countersink Gage
Used to measure the reamed starting hole for a forcemate bushing installation on the f-16;
01-561-8021
Plug Countersink Gage
Used to measure the reamed starting hole for a forcemate bushing installation on the f-16;
01-562-0378
Plug Plain Cylindrical Gage
The verification pin is a double end gage used to check the starting hole & installed retainer inside diamete. the stepped blade end is used to check the starting hole for size & ovality. the other end is used to verify the retainer's inside diameter after installation. fastener size: 3/16 in; retainer size: ; class of fit: class iii
01-562-0801
Profile Gage
Fastener size: 3/16 inch; retainer size: only mandrel check fixtures are used for & oversize retainers; class of fit: class iii. the mandrel check fixture is used to verify that the mandrel major diameter is not worn below its allowable dimension. if the mandrel major diameter can slide through the hole in the mandrel check fixture, the mandrelis dscarded & replaced.
01-562-1734
Thickness Electronic Gage
4.500" overall length 2.500" overall width
01-562-3060
Crimping Tool Gage
01-562-3779
Crimping Tool Gage
01-563-8061
Contact Electrical Connecto Gage
Contact spring gage; go/no go gauge this item measures the contact pressure of moving contacts
01-563-8091
Contact Electrical Connecto Gage
Contact spring gage; go/no go guage this item measures the contact pressure of moving contacts
01-563-8108
Contact Electrical Connecto Gage
Contact spring gage; go/no go guage item measures contact pressure of moving contacts
01-563-9678
Profile Gage
Used on torpedo mk48 program.
01-564-1452
Profile Gage
Used on adcap program. gage which is 1.500" wide; has 2 thru holes 1.500" apart, one having a 0.381 inch diameter, the other with a 0.512 inch diameter centered on gage
01-564-7589
Plug Thread Gage
Go gage pitch dia min. 5.6959 andmax. 5.6965; no-go gage pitch dia min.5.7043
01-564-8609
Toolmaker's Flat
Used on 4940-01-551-2884, maintenance facility, transportable. toolmakers flat has round pink granite plate; top
01-565-5072
Profile Gage
Used on gage set - canopy - jettison release. gage being 0.500" wide, having two underside cut outs 0.4 x 0.5"
01-565-5706
Angle Solid Plate
