01-485-1573
Profile Gage
Used on f100-pw-100/200/220e. used to hold respective uniball bearing housing while motion is registered on dial indicator
01-485-2177
Profile Gage
Used on f22 aircraft. name submitted is gage, rail wear
01-485-3431
Profile Gage
Used on f100-pw/200/200/220e. used to hold bearing housing while bearing is moved back
01-485-7931
Profile Gage
Used on common rack and launcher test set (cralts). marking: W29-red
01-485-7940
Profile Gage
Used on common rack and launcher test set (cralts). marking: W29-green
01-485-7995
Ring Master Setting Gage
Used to verify id gage PWA72498 for diameter setting of 7.080, used on F100/200/220/22e engines
01-485-7997
Ring Master Setting Gage
Used to verify the settings of PWA72545 id gage setting of 16.277in, used on F100/200/220/220e engines
01-485-7999
Profile Gage
Used on F100-pw/200/220/220e engines
01-485-8018
Profile Gage
Used on f100-pw-229. gage, bore-no. 3 bearing air seal, rear snap diameter (5.6500) used to position, hold, and round up air seals to provide concentricity
01-485-8296
Profile Gage
Gage is stored in a wooden container when not in use, setmaster are required to preset dial bore gages to zeroprior to each use, required calibrationevery 18 months
01-485-9574
Ring Master Setting Gage
Used on f100-pw-229. setmaster-no 3 bearing air seal, forward snap diameter; used to pre-set PWA72504 gage to zero prior to use; also used for to verify the integrity of the hydraulic chuck detail of PWA72489 machining fixture during set up; inner diameter: 5.60125 in; tolerance: plus 0.00025 in; ov dia 8.0 in; ht 1.5 in; wt 2 lbs
01-485-9575
Flush Pin Plain Cylindrical Gage
Used on f100-pw-220/220e. gage, flush pin-no 5 bearing seal support, piston ring groove used to assure 0.005 in clean-up dimension does not exceed allowable 1.695 in prior to nickel plate restoration of seal support p/n 4027961; measures depth of lower groove face from an aft datum surface
01-485-9593
Profile Gage
Used on f100-pw-229 engine. gage-combustor deflector erosion; used to visually check the deflector for excessive wear while installed in the combustion chamber
01-486-0307
Profile Gage
Used on f100-pw-229. used for measuring the repairability of 3rd stage (forward end of 26.764) , (aft end of 27.514)
01-486-1328
Disk Master Setting Gage
Used on f100-pw-100,200,220,220e. set master, 1st stage turbine, stator support, outer; used to check the integrity of PWA72326 fixture prior to finish machine of weld repaired 1st stage turbine stator outer support lugs
01-486-2335
Profile Gage
Used on f100-pw-229 engine. dused to measure amount of stretchencountered by turbine blade at depot levelmaintenance; does same job as PWA57138 (5220-01-196-4337) ; used with PWA17019 (5210-00-821-7438) (dial indicator; serd 8988
01-486-3127
Crimping Tool Gage
01-486-3128
Crimping Tool Gage
01-486-3129
Crimping Tool Gage
01-486-3130
Crimping Tool Gage
01-486-6388
Profile Gage
Used on f100-pw-229. gage, indicator-no 3 bearing air seal, middle knife edge; used to measure the diameter of the middle knife edge to 7.080 in; ln 12.0 in; wd 3.0 in; ht 3.0 in; wt 10.0 lbs
01-486-7171
Profile Gage
Matl, aisi 4140, case hardened to rc 58-60 to a depth of .015-.020; fin, oxide, grayish black in color; dwg name, gage, inspection-fitting metric, soft permaswage; tube size 0.473
01-486-7173
Profile Gage
Matl, aisi 4140, case hardened to rc 58-60 to a depth of .015-.020; fin, oxide, grayish black in color; dwg name, gage, inspection-fitting metric, soft permaswage; tube size 0..630
01-486-9075
Profile Gage
Manufacturers item name: go/no-go gage
01-486-9081
Profile Gage
Manufacturers item name: go/no-go gage
01-486-9082
Profile Gage
Manufacturers item name: go/no-go gage
01-487-8365
Profile Gage
Used on f100 engine. fixture is required to inspect the 3rd stage turbine blade length to determine if the blade is within the service limits, fixture measures the length from the root z plane to blade end, fixture design will have a built in shop service calibration feature with electronic precision dial attached to a slide bar, flush pin; dwg name is fixture, inspection 3rd stage turbine blade, length
01-488-3937
Ring Master Setting Gage
Used on ring, master setting. this master setting ring is used in conjunction with the p/n DA132MO740-1 air jet plug, this will provide the means to measure the internal diameters of the housing bores.
01-488-5156
Profile Gage
Head space dimensions- 3.1392"
01-488-5530
Comparator Electronic Gage
Used on 5220-01-156-3968, f-16 support equipment. splashproof (ball bearing) , diameter: 0.375in, length: 2.370in
01-488-8929
Crimping Tool Gage
01-490-4167
Profile Gage
Used on f100-pw-100/200220/220e. used to preset PWA72617 gage to "0" prior to use, when measuring repair dia. (ref:29.812 in.) of turbine case
01-490-4363
Ring Master Setting Gage
Used on special aircraft and engine tool support equipment. chrome plated; certification to class xx
01-490-6793
Profile Gage
Used on f110-ge-129, f-16 support equipment. size: 8.5in x 6.5in x 3.3in
01-490-7164
Ring Master Setting Gage
Used on f100-pw-229 engine. NPWA72604 set master consists of set of (3) aisi A2 steel rings having precision inner bore dimension, each detail master has a dimension marked on an end surface ref: 5.0950/5.0944, 5.1402/5.1394, or 5.5002/5.4994
01-490-7174
Profile Gage
Used on c-17acft. replaces 5220-01-279-3988
01-491-0000
Profile Gage
Used on f100-pw-100/200/220/220e/229 engine. dwg name gage-spline, rear compressor drive shaft torque adapter simulator. installed as a go-no-go gage to insure the drive shaft is round
01-491-8613
Comparator Electronic Gage
Used on af metcal; ground support equipment. computerized version of model 130b-24; provides solid state electronic surveillance
01-492-1039
Contact Electrical Connecto Gage
01-492-1041
Contact Electrical Connecto Gage
01-492-7550
Profile Gage
Used on machine gun, caliber 50 and 30.
01-492-9056
Profile Gage
Used on machine gun, caliber 50 and 30.
01-493-2375
Coating Thickness Gage
01-493-3479
Disk Master Setting Gage
Used on f100-pw-100/200/220/220e/229. consists of a steel ring with 3 pressed positioning pins extending into the inner diameter of the ring
01-493-3537
Disk Master Setting Gage
Used on F100. consists of a steel precision ring w/inner dia of 10.495-10.500 in. simulating max. hydraulic chuck expansion of companion tool pwa 72557 fixture
01-493-4392
Ring Master Setting Gage
Used on f100-pw-100/200/220/220e engine. dwg name master set, spark erosion-3rd stage turbine air seal ring; honeycomb; height 2.5 in, length
01-493-8018
Profile Gage
Used on serd9492,f100-pw-229engines. 9.60in high x 36.25in length; reqrd for weld repair of pn 4071179; supports-locates flameholder assy on clevis after riveting saddle in place/verifies location is correct
