01-386-8819
Profile Gage
Used on f100-pw-220. 1.800in oah x 4.500in lg x 4.500in wd; to provide reference flow indication for calibrating eddy current probeand instrumentation prior to conducting eddy current inspection of 1st turbine front retaining plate; serd 7055
01-386-8830
Profile Gage
Used on 117 engine. gage used w/PWA81946 fixture to find if height of knife edge of lpt blade is worn below its limit; 3.2in. wd by 2.0 in. ht; 5.0 lbs; gage is awelded steel assy w/bottom
01-386-8836
Flush Pin Plain Cylindrical Gage
Used on f100-pw-229. 28.0 in. lg by 1.0 in. wd by 0.8 in. ht; used w/PWA71014 machine fixture; engine part supported 4075983; rqrd for pre-inspection procedures assoc w/plasma spray repair of 3rd stage compressor stator anti-rotation flange face; c/o tool steel bar w/indicator, holder
01-386-9143
Profile Gage
Used on 117 engine;serd 1118. gage, twist; 6.0 in. lg by 2.5 in. wd by 4.5 in. ht; 3.5 lbs; rqrd to measure the shroud twist of the fifth stage low pressure turbine; c/o yoke base that attaches to a check
01-386-9466
Profile Gage
Fixture, inspection - combustor assyemly
01-387-0366
Comparator Electronic Gage
Used on f100-pw-220. used to provide a reference flaw indication for calibrating eddy current probe
01-387-0444
Thickness Electronic Gage
01-387-5306
Profile Gage
Used on 117 engine. rqrd to inspect low pressure turbine case third stage vane retaining rail for wear; c/o "l" shaped steel blockof welded construction; plastic box provided for storage; 4.5 in. lg by 3.0 in. wd by 2.5 in. ht; 3 lbs; serd 1094
01-387-5316
Profile Gage
Used on 117 engine. rqrd to inspect low pressure turbine case seventh stage vane retaining rail for wear; c/o "l" shaped steel block of welded construction; plastic box provided for storage; 10.0 in. lg by 3.0 in.wd by 3.0 in. ht; 4 lbs; serd 1098
01-387-5320
Profile Gage
Used on 117 engine. 9rqrd to determine height of knifeedge of low pressure turbine blade below its min limit; gage is a welded steel assy w/bottom
01-387-5323
Profile Gage
Used on 117 engine. rqrd to inspect low pressure turbine case fifth stage vane retaining rail for wear; c/o "l" shaped steel blockof welded construction; plastic box provided for storage; 7.5 in. lg by 3.0 in. wd by 2.5 in. ht; 3.5 lbs; serd 1096
01-387-5325
Profile Gage
Used on 117 engine. rqrd to determine if height of knife edge of low pressure turbine bladeis worn below its limit; gage is a welded steel assy w/bottom
01-387-5637
Profile Gage
Gage, inspection; rectangular steel base; 2 precision locator assemblies
01-387-7722
Profile Gage
Used on f117-pw-100. gage required to inspect low pressure turbine case 4th stage vane retaining rail for wear; serd 1095
01-387-9383
Profile Gage
Used on f117-pw-100. gage required to inspect low pressure turbine case 6th stage vane retaining rail for wear; serd 1097
01-387-9705
Plug Plain Cylindrical Gage
Used on dw f117pw100 eng. ball bearing contact angle gage
01-387-9728
Plug Plain Cylindrical Gage
Inspection combustion assembly fixture
01-388-1330
Profile Gage
Gage, inspection; used for dimensional shroud inspection of the 7th turbine blade; size: 13.700 x 7.300 x 5.000 in
01-388-1460
Profile Gage
Used on gnsn 2320-01-097-0260 hemtt (heavy expanded mobility tactical truck); w/s:family of medium tactical vehicles-medium; truck, heavy expanded mobility tactical (hemtt); truck, m-915 series, m-916a1 (let). torque converter end play gage
01-388-1482
Toolmakers Button Set
Material:ledloy, heat treat:carburized 75-77 R30n, finish: black oxide.
01-388-1514
Flush Pin Plain Cylindrical Gage
Used to check mandrel wear.sized to the allowable major diameter of the mandrel. made from hardened steel.
01-388-1683
Plug Plain Cylindrical Gage
Blade configuration is flat on two sides to detect hole ovality.
01-388-1692
Plug Plain Cylindrical Gage
Blade configuration is flat on two sides to detect hole ovality.
01-388-1722
Flush Pin Plain Cylindrical Gage
Used to check mandrel wear. sized to the allowable major diameter of the mandrel. made from hardened steel.
01-388-1727
Plug Plain Cylindrical Gage
Blade configuration is flat on two sides to detect hole ovality.
01-388-1736
Flush Pin Plain Cylindrical Gage
01-388-1740
Flush Pin Plain Cylindrical Gage
Used to check mandrel wear. sized to the allowable major diameter of the mandrel. made from hardened steel.
01-388-2214
Profile Gage
Used on 1520011069519. gage, 30mm aws rotor go-no-go
01-389-3223
Profile Gage
Used on 4920-01-216-0455.
01-389-7264
Angle Solid Plate
Used on 2350-01-248-7620. material; aluminum 5083-hiii
01-389-7278
Angle Adjustable Plate
Material; 1020 steel, black oxide finish per mil.spec - c-13924a.
01-390-1851
Comparator Electronic Gage
Max tool lg 20.0 in.; max tool DIA11.0 in.; utility rqmts air 30 psi, electrics 240v/110v 60 hz single phase OR100v/220v 50 hz single phase; no. 45 OR50 master spindle socket; dimensions front to back 24 in., left to right 18 in., height 69-1/4 in., net wt 320 lbs; led display; zero reset; digital keyboard;
01-390-3222
Plug Plain Cylindrical Gage
01-390-6915
Profile Gage
Used on f117-pw-100. required to check clearance between the low pressure turbine case
01-391-1846
Disk Master Setting Gage
Used on fixture,inspect hp compressor stator liner-stg 2. matl:stl, sae 01
01-391-6468
Profile Gage
Used on 1520-01-106-9519.
01-392-1065
Crimping Tool Gage
01-392-6068
Crimping Tool Gage
01-392-6897
Disk Master Setting Gage
Fgage, diameter, master setting; required to set PWA83029 indicator gage to basic diam. to check hpc rear case 13th stage groove at premachine oper prior to plating
01-392-7021
Disk Master Setting Gage
Used on 92 f110-100 cip.
01-392-8248
Profile Gage
Used on f117-pw-100. gage, stretch; consists of machine & bench adjuster; base assy; several adj. knobs to inspect blades for wear; storage container, serd number 1582
01-392-8249
Profile Gage
Used on f117-pw-100;serd 1462. gage, length, indicating; used to check blade tip length during grinding oper on 6th-17th stage high pressure compressor blades; 3 in. lg x 2.5 in. high x 0.800 in. wd
01-393-2387
Coating Thickness Gage
Used on c-17 engine.
01-393-8583
Profile Gage
Gage, linear movement; used to measure freeplay of piston
01-393-9164
Profile Gage
Used on 117 engine. c/o dial indicator holder, master set block, template gage
01-394-0683
Crimping Tool Gage
Gage 2.500 length; pin 0.500" length each end; pin material alloy tool steel qq-t-570 class optional, harden to rockwell C62-C65; chrome flash finish 0.0002/0.0003" thickness per qq-c-320 class 2; handle made of aluminum alloy no. 2w per commerical std CS8; pin go diameter 0.2865"; pin no-go diameter 0.2935"
01-394-3335
Profile Gage
Used on seawolf submarine.
01-394-4326
Profile Gage
Used on c-17 acft. arqrd to check the mlg drag links for proper adjustment; matl steel; finish passivate; 1.861 in. lg by 2.50 in. ht by 1.00 in. wd
01-395-0591
Profile Gage
SERD450136
