01-384-9791
Profile Gage
Used on c-17,serd 1259. c/o hardened tool steel blank; used with holder
01-384-9802
Positioning Table
22.000" overall length 22.000" overall width mounts under test measuring stage; measurements performed using focus/positioning control
01-384-9808
Profile Gage
Used on c-17,serd 1261. c/o hardened tool steel blank; rqrd to gage length of sixteenth stage blades of high pressure compressor; used with holder
01-384-9809
Profile Gage
Used on c-17,serd 1417. rqrd to inspect length of ninth stage high pressure compressor blade; hardened steel machined blank; 0.80 in. lg by 0.40 in. wd by 3.50 in. ht
01-385-5051
Profile Gage
Gauge provides an accurate method of achieving the proper adjustment of poppet of the 64349 carter underwing refueling nozzle.the gauge can be used on all of carter's underwing nozzles.
01-385-6654
Coating Thickness Gage
Used on f-100-220 engine.
01-385-7594
Profile Gage
Used on f117-pw-100. required to check service limit size of combustion chamber fuel injector guide diameter
01-385-7606
Profile Gage
Used on f117-pw-100. required to check combustion chamber inner liner length
01-385-7611
Profile Gage
Used on f117-pw-100. required to check fuel injector guide height
01-385-7613
Plug Plain Cylindrical Gage
Used on f117-pw-100. plug gage required to check combustion chamber mount lug bushing clearance
01-385-7617
Disk Master Setting Gage
Used on f100-pw-100/200/dp/220/220e. master gage required for snap gage 10.987/10.991o.d.
01-385-8518
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. rqrd to inspect 4000 cycle/ilc core hpt disk o.d. front snap dia; incorporates electronic output for diametrical measurement as well as heat sensor to measure disk temperature during snap diameter inspection; must be set using master PWA56529; constrained in fixture pwa 7745025; 3rd stage compr disk 17.506-17.508 o.d. front; serd 6650
01-385-8519
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. rqrd to inspect 4000 cycle/ilc core hpt disk o.d. front snap dia; incorporates electronic output for diametrical measurement as well as heat sensor to measure disk temperature during snap diameter inspection; must be set using master PWA56553; constrained in fixture PWA56548; 2nd stage hpt disk 17.560-15.584 o.d. front; serd 6672
01-385-8526
Snap Fixed Gage
Used on f100-pw-100/100/dp/220/220e. rqrd to inspect 4000 cycle/ilc core hpt disk o.d. front snap dia; incorporates electronic output for diametrical measurement as well as heat sensor to measure disk temperature during snap diameter inspection; must be set using master PWA56543; constrained in fixture PWA56537; 1st stage hpt disk 15.820-15.834 o.d. front; serd 6662
01-385-8530
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. rqrd to inspect 4000 cycle/ilc core hpt disk i.d. front snap dia; incorporates electronic output for diametrical measurement as well as heat sensor to measure disk temperature during snap diameter inspection; must be set using master PWA56543; constrained in fixture PWA56537; 1st stage hpt disk 14.047-14.051 i.d. front; serd 6660
01-385-8533
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. rqrd to inspect 4000 cycle/ilc core hpt disk o.d. front snap dia; incorporates electronic output for diametrical measurement as well as heat sensor to measure disk temperature during snap diameter inspection; must be set using master PWA56553; constrained in fixture PWA56548; 2nd stage hpt disk 15.957-15.961 i.d. front; serd 6670
01-385-9451
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. gage, master, snap; rqrd to set gages PWA56539
01-385-9454
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. gage, master, snap; rqrd to set gages PWA56550
01-386-0185
Plug Plain Cylindrical Gage
Used on f117-pw-100. plug gage required to check inside clearance of combustion chamber igniter guide
01-386-1078
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. 18.0 in. jg by 4.0 in. wd by 6.0 in. ht; 9.0 lbs; rqrd to inspect 4000 cycle/ilc core hpt disk o.d. rear snap dia; incorporates electronic output for diametrical measurement as well as heat sensor to measrure disk temperature during inspection; uses master PWA56547; constrained in fixture PWA56544; serd 6667
01-386-1097
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. 15.551-15.555id front
01-386-1123
Snap Fixed Gage
Used on f100-pw-100/200/dp/220-220e. 15.551-15.555i.d.
01-386-1130
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e.
01-386-1141
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. 11.238-11.243o.d. front; serd 6671
01-386-1168
Snap Fixed Gage
Used on f100-pw-100/200/dp/220-220e. 9.324-9.328i.d. front; serd 6661
01-386-1185
Snap Fixed Gage
Used on f100-pw-100/200/dp/220-220e. 18.024-18.026o.d.rear; SERD6649
01-386-1201
Snap Fixed Gage
Used on f100-pw-100/200/dp/220/220e. 15.957-15.961i.d. front; serd 6673
01-386-1234
Profile Gage
Used on 117 engine. vrqrd to determine if first stage turbine vane airfoil tkns is acceptable; c/o 3 u-shaped templates at 3 airfoil sections of the vane; 2.7 in. lg by 1.5 in. wd by 2.0 in. ht; storage dim. 5.3 in. ln by 5.3 in. wd by 4.0 in. ht; 1.2 lb
01-386-1240
Comparator Electronic Gage
Used on 117 engine. matl carbide
01-386-1250
Comparator Electronic Gage
Used on 117 engine. required to measure sq inch area value of 1st stage turbine stator vaneassy when using computer enhanced method; gage is steel
01-386-1277
Profile Gage
Used on 117 engine. required to check chord lg of 6th stage compressor blades; gage is a steel bar w/4 dowel pins at one end, 2 locate end of blade
01-386-1289
Comparator Electronic Gage
Used on 117 engine. matl carbide
01-386-1293
Coating Thickness Gage
Used on f100pw229.
01-386-1296
Comparator Electronic Gage
Used on 117 engine. required to measure sq inch area of 2nd stage non-pair turbine vane assy, 2nd stage welded cluster turbine vane assy, 2nd stage non-welded cluster turbine vane assy when using computer enhanced method; gage is steel
01-386-2007
Flush Pin Plain Cylindrical Gage
Used on f100-pw-229. required to inspect rear outer surface during finish machining operation after plasma spray; gage will check the 0.475/0.469 drop dimension while part is fixtured; serd 7074
01-386-2010
Flush Pin Plain Cylindrical Gage
Used on f100-pw-229. required to check 3rd stage compressor stator dimension to inner platform trailing edge surface; 1.786/1.782 dimension; gage may also be used to inspect depth of wear prior to repair; SERD7080
01-386-2012
Flush Pin Plain Cylindrical Gage
Used on f100-pw-229. required to check 3rd stage compressor stator dimension to anti-rotation flange front inner face; 0.350/0.340 dimension; gage may also be used to inspect depth of wear prior to repair; serd 7082
01-386-2013
Profile Gage
Used on f100-pw-229. serd 7069; 4.0 in. lg by 1.0 in. wd by 2.5 in. ht; 3.0 lbs; c/o tool steelbase w/flush pin
01-386-2017
Profile Gage
Used on 117 engine. serd 0747; 1.0 in. wd; 1.0 in. ht; 1.0 lb; c/o narrow rectangular hardened steel block w/vertical legs of closelycontrolled height at both ends; legs differ in ht
01-386-2033
Profile Gage
Used on 117 engine. serd 0747; 1.0 in. wd; 1.0 in. ht; 1.0 lb; c/o narrow rectangular hardened steel block w/vertical legs of closelycontrolled height at both ends; legs differ in ht
01-386-2034
Flush Pin Plain Cylindrical Gage
Used on f100-pw-229. required to check 3rd stage compressor stator dimension to anti-rotation flange front inner face; 0.370/0.360 dimension to pre-machining operation prior to plasma spray; serd 7087
01-386-2035
Profile Gage
Used on f100-pw-229. serd 7075; 4.0 in. lg by 1.0 in. wd by 2.5 in. ht; 3.0 lbs; c/o tool steelbase w/flush pin
01-386-2037
Profile Gage
Used on 117 engine. wserd 1414; 5.3 in. lg by 0.8 in. wd by 0.5 in. ht; 0.1 lb; rqrd to inspectlength of sixth stage high pressure compressor blade; master is hardened steel machined blank dimensioned to simulate level of acceptability of a specific blade
01-386-2038
Flush Pin Plain Cylindrical Gage
Used on f100-pw-229. 28.000" overall length serd 7081; 1.0 in. wd by 0.8 in. ht; 6.0 lbs; locates support surface of PWA71014 machine fixture to measure stator dimension 0.302/0.298 to anti-rotation flange front outer face, after plasma spray; also inspects wear depth; c/otool steel bar w/indicator, holder
01-386-2743
Contact Electrical Connecto Gage
01-386-2882
Profile Gage
Used on f117-pw-100. required to be a standard when measuring the 2nd stage turbine blade growth; serd 1546
01-386-3808
Disk Master Setting Gage
Used on f117-pw-100. egage, master, inspection; necessary to prepare for the inspection
01-386-7094
Profile Gage
Used on 117 engine. serd 0394; rqrd to check radial movement rqrd in combustion fuel injector guide; 9.4 in. lg by 1.8 in. dia; gageplug is steel rod c/o a handle, controlled dia w/flange, and tang; tang is at right angle to the axis of diameters
01-386-7096
Profile Gage
Used on 117 engine. rqrd to check axial location of combuster chamber igniter guide; gage isa steel rod c/o handle, flanged controlled dia with go/no-go whistle notch
01-386-7551
Contact Electrical Connecto Gage
