01-363-0388
Flush Pin Plain Cylindrical Gage
Used on engine model gtcp36,small gas turbine. weight: 1 lb.; material: stainless steel; finish: natural; envelope dims: 2.75 x 1.50 x 3.0 in.; used to obtain measurements to determine quantity of shims required to obtain specified monopole clearance
01-363-2561
Comparator Electronic Gage
Laser scan for non-contact measurements
01-363-6942
Snap Plain Adjustable Gage
Used on ground and airborne gas turbine engines,aux. power units accessories and parts. weight: 15 lbs.; material: steel; finish: black oxide; dimensions: 10.0 x 7.25 x 4.0 in.
01-364-0305
Plug Thread Gage
Right-hand
01-364-2995
Comparator Electronic Gage
Laser scan for non-contact measurements
01-364-4095
Ring Master Setting Gage
Gage kit, ring, master setting; kit c/o 28 sets of master setting ring gages, used to calibrate probes; listed are part numbers of each gage set: MSI278-09-1, 2; MSI278-09-3, 4; MSI278-09-5, 6; MSI278-09-7, 8; MSI278-10-1, 2; MSI278-10-3, 4; MSI278-10-5, 6; MSI278-10-7, 8; MSI278-11-1, 2; MSI278-11-3, 4; MSI278-11-5, 6; MSI278-11-7, 8; MSI278-12-1, 2; MSI278-12-3, 4; MSI278-12-5, 6; MSI278-12-7, 8; MSI278-14-1, 2; MSI278-14-3, 4; MSI278-14-5, 6; MSI278-14-7, 8; MSI278-40-11, 2; MSI278-40-1, 2; MSI278-40-3, 4; MSI278-40-5, 6; MSI278-15-1, 2; MSI278-15-3, 4; MSI278-15-5, 6; MSI278-15-7, 8
01-364-4872
Profile Gage
Used on aircraft ep-3c.
01-364-8949
Comparator Electronic Gage
Gage, head, electronic; lever type; protected agains outside magnetic fields; gaging pressure - 10 grams measured in vertical position w/contact point downward; cable length 7 feet; dovetail mounting; 3.54 in. by 0.59 in. 0.67 in.; spindle pre-travel .002 in.; measuring travel +/- .012 in.; over-travel .002 in.; repeatability +/-s .000004 in.; hysteresis error .00001 in.; rqrd to perform precisiion measurements of test fixtures defined in serd no. 0089; connects to pretec digital comparator
01-366-1781
Comparator Air Gage
01-368-1556
Plug Plain Cylindrical Gage
Plug gage is a class xx, go, no go, reversible cylindrical handle type gage
01-368-1557
Comparator Air Plu Gaging Member
Used during depot maintenance of pump
01-368-2741
Angle Solid Plate
01-368-2742
Angle Solid Plate
01-368-3270
Profile Gage
Material is stainless steel shaped to profile impeller vanes; used to control amount of stock removed from surface of vane
01-369-4384
Ring Master Setting Gage
End item f-15e
01-369-4385
Ring Master Setting Gage
End item f-15e
01-369-8143
Comparator Air Gage
01-370-3184
Parallel
18.000" overall length 1.500" overall width granite
01-370-3825
Profile Gage
Matl tool steel; wt 8 oz.; size 1.5 in. dia by 1.0 in.; rqrd to determine limits
01-370-5268
Ring Master Setting Gage
01-370-6168
Plug Plain Cylindrical Gage
01-370-6169
Profile Gage
Handle is 3in long with replaceable gage member
01-370-8217
Plug Plain Cylindrical Gage
01-370-8706
Profile Gage
Rqrd for visual inspection of breech erosion in bru-46/a
01-371-4219
Angle Solid Plate
01-372-2612
Ring Plain Gage
01-372-2613
Ring Plain Gage
01-372-2978
Ring Plain Gage
01-372-5668
Measuring Tool Case
01-372-6014
Comparator Electronic Gage
01-372-6993
Profile Gage
Used on 6145013164648.
01-373-0186
Disk Master Setting Gage
This gage has known defects, and used to perform calibration prior to running F100-229 engine parts, it is a reoperated engine part; used when operator has performed prestart checks on holographic inspection test stand p/n PWA54900; gage master installed on excitation plate when operator sets up test stand for 5th stage compressor stator segment; rqrd prior to performing bond inspection of F100 engine parts; engine p/n 4078485
01-373-4615
Profile Gage
Gage, inspection, master setting; steel beam w/ rest surfaces having a preset diameter between anvil blocks
01-373-4618
Profile Gage
Gage, inspection, master setting; tool is a steel beam w/rest surfaces that has a preset diam. between anvil blocks; this tool is used to verify the diam. w/indicator gage PWA70737
01-373-4619
Profile Gage
Gage, inspection, master setting; steel beam w/ rest surfaces having a preset diameter between anvil blocks
01-373-4620
Profile Gage
Gage, inspection, master setting; used to calibrate the holographic inspection test stand
01-373-4621
Profile Gage
Gage, inspection, master setting; used to calibrate the holographic inspection test stand
01-373-7249
Plug Plain Cylindrical Gage
01-373-8069
Plug Plain Cylindrical Gage
01-373-8070
Plug Plain Cylindrical Gage
01-373-8071
Profile Gage
Material 17-4ph cres per AMS5604 stock size 0.375
01-373-8630
Flush Pin Plain Cylindrical Gage
01-373-8631
Flush Pin Plain Cylindrical Gage
01-373-8632
Flush Pin Plain Cylindrical Gage
01-374-0216
Profile Gage
Required to set up PWA56517 machining fixture w/0.004" offset. the 0.004" offset will be built into the master & will simulate clocking
01-374-1340
Plug Plain Cylindrical Gage
Used on seahawk helicopter,s70b-2.
01-374-1341
Profile Gage
Used on h-60 helo. to fit in the i.d. of the bushings, and with the use of a feeler gauge wear will be measured
01-375-7954
Plug Plain Cylindrical Gage
Used on 19 f15e aircraft.
01-376-1602
Measuring Anvil
Used on fn 5180-01-267-7643.
01-376-1603
Measuring Anvil
Used on fn 5180-01-267-7643.
