01-386-4617
Gap Setting Gage
01-386-4620
Hole Sizing And Loc Gage Pin Set
01-386-4640
Hole Sizing And Loc Gage Pin Set
01-386-4657
Hole Sizing And Loc Gage Pin Set
01-386-6855
Electronic Level
Combines accuracy to 1/2 degree; determines both horizontal
01-386-6909
Measuring Tape
Modification permits 1/8 inch tactual reading at any point on the tape by the use of a 6 inch tactually marked extension permanently attached to the case; each foot-mark is brailled; each 6 inch has a single raised dot on the lower edge that lines up with the end of the extension; push-button controlled blade return; positive blade locking; removable belt grip; 6.09 m (20 feet)
01-386-6910
Hook Rule
Clicks at each 1/16 inch
01-386-7213
Surface Gage
Used on p/n 16-251-b, board 210 ft wmec mma coast guard vessels.
01-386-7698
Hook Rule
Telescopic click rule clicks at each 1/16 inch
01-386-7898
Indicating Internal Gage
Used on f100-pw-229. c/o steel u-channel w/integral dial indicator
01-386-8815
Height Gage
Used on f100-220 engine. rqrd to inspect honeycomb height of the 10th stage compressor stator honeycomb dia; 1.0 by 16.4 bar w/dowel flush pin incorporated into bar
01-386-8857
Thickness Dial Indicating Gage
01-387-0430
Height Gage
Used on f100-pw-229. K5.0 in. ht; c/o l-shaped steel block approx 5 in. sq by 0.75 in. wd w/an integral gage pin to indicate the honeycomb step height; rqrd to verify repaired
01-387-1782
Depth Dial Indicating Gage
01-387-1806
Depth Dial Indicating Gage
Used on used in support of pre-provisioning items for which navicp-phil acts as a poe.
01-387-1914
Indicating Internal Gage
Used on f100-220. used w/master set PWA70827; enginepart supported 4060645; rqrd to repair 5th stage compressor shroud for cip 506 task 311-17x; item is a steel i.d. bridge gage w/dial indicator capable of measuring 15.740 dia of honeycomb replacement airseal after machining; serd 6825
01-387-1934
Indicating Internal Gage
Used on f100-220. serd 6829; used w/master set PWA70831; engine part supported 4060645; usedto repair 5th stage compressor shroud for cip 506 task 311-17x; item is a steel i.d. bridge gage w/dial indicator capable of measuring 15.962 dia of honeycomb replacement airseal after machining
01-387-2722
Dial Indicator
01-387-4279
Thickness Dial Indicating Gage
Used on 117 engine.
01-387-4354
Thickness Dial Indicating Gage
Used on 117 engine.
01-387-4902
Thickness Dial Indicating Gage
Used on 117 engine.
01-387-5433
Outside Caliper
01-387-5468
Thickness Dial Indicating Gage
Used on f117-pw-100.
01-387-5476
Height Gage
Used on f117-pw-100. 11.100in length x 2.900inwide x 2.000in high; gage used to determine if height of knife edge of low pressure turbine blade is worn below its limit; serd 1126
01-387-5482
Thickness Dial Indicating Gage
Used on f117-pw-100.
01-387-5483
Thickness Dial Indicating Gage
Used on f117-pw-100.
01-387-5484
Height Gage
Used on f117-pw-100. length 6.000in x 3.300in wide x 2.000in high; gage required to determine if height of knife edge of low pressure turbine blade is worn below limit; serd 1122
01-387-5486
Thickness Dial Indicating Gage
Used on f117-pw-100.
01-387-5487
Height Gage
Used on f100-pw-100/200/220/220e. required to perform inspection ofthe honeycomb step height during machining; serd 6831
01-387-5491
Indicating Internal Gage
Used on f100-pw-100/200/220/220e. 15.850 plus/minus 0.002; to measure the honeycomb during repair on shroud before part is removed from fixture; serd 6827
01-387-5492
Thickness Dial Indicating Gage
Used on f117-pw-100.
01-387-7352
Micrometer Inside Caliper
8 pieces to the set; used with assembly 005
01-388-3740
Depth Drill Bit Gage
Used on 1015-01-226-1672.
01-388-4039
Indicator Outside Caliper
Used on 117 engine.
01-388-4907
Height Gage
Used on f117-pw-100. to measure axial deflection of 3rd stage turbine vane cluster
01-388-4938
Thickness Dial Indicating Gage
Used on 117 engine.
01-389-1217
Depth Micrometer Gage
Used on general electric turbine.
01-389-6268
Cannon Bore Erosion Gage
End item is ac-130u 25mm gun; serdnumber is 0001
01-389-9291
Height Gage
Atwo-column const; carbide-tipped scriber; two-directional touch probe; zero set stand-by; (3) aa batteries pwr; optional equip is 192-001 (probe) ; 937243 (conn cable) ; 264-500 dp-1; 449100 (wooden case)
01-390-4135
Thickness Dial Indicating Gage
Used on c-17 engine.
01-390-9463
Hinge Butt Door And Jam Template
01-391-0224
Cylindrical Circular Vial Level
Used on mark 20.
01-391-3542
Height Gage
Support arms are stepped at one end (.218in. dia.) for swivel clamp (cp-2199) ; base have on/off switch; base dim. 4.5X1.9X2.2in.h., main post length 15.8in., dia. .79in.; support arm length 7.9in., dia. .55in.; post clamp
01-392-1696
Thickness Dial Indicating Gage
01-392-7067
Measuring Tape
01-392-8335
Height Gage
Prqrd to check combustion chamber fuel injector guide height after repair of combustion chamber fuel guide supports; notches on gage represent min
01-392-8874
Dial Indicator
Used on cummins no. 3822575 injector and valve adjustment kit.
01-392-8891
Dial Indicator
01-393-1085
Micrometer Head
Cover include; thread pitch 50.8
