01-520-6606
Counterbore Pilot
Pilot dia. 0.563 in; pilot material steel
01-520-7270
Machine Solid Mandrel
26.000" overall length mandrel assy 20mm gun rough machine mandrel heat treat to RC36; machined roughness shall be 125 rhr or better
01-520-8648
Abrasive Wheel
Mounts on right-angle, portable air
01-520-9098
Machine Collet
Collet, solid, 1/4 .2505 1/4, 0.2505; for use with 1/4 inch cutters
01-520-9198
Abrasive Wheel
Adjustable wheel guard; o/a length 19.250 inch; air inlet 3/8-npt
01-522-0359
Machine Collet
01-522-0360
Machine Collet
End item: ref
01-522-4922
Machine Solid Mandrel
01-522-4975
Abrasive Wheel
Used on baldor electric bench grinding machine.
01-522-4976
Abrasive Wheel Dresser Stand
Used on baldor electric bench grinding machine.
01-523-6261
Magnetic Chuck
01-523-6915
Machine Collet
Locator
01-523-6916
Machine Collet
Jaws
01-523-6918
Machine Hold Down Clamp
Used on semi-rigid tools. holding fixture
01-523-6920
Machine Collet
Split concentrator
01-524-0516
Positioning Table
12.200" overall length rotary table machine attachment-tilting optional slot; indexing accuracy horizontal position plus or minus 10 seconds; vertical position plus or minus 20 seconds; tilt plus or minus 20; table flatness within 0.0005 in; concentricity within 0.0002 in; 1 revolution of the dial drum is 3 degrees; weightmax 300 lbs
01-524-5652
Abrasive Wheel
Has common nylon threaded male (screw type) hub; easily mounts to either lockit or reloc holder pads with a half turn; stays securely in place for the life of the disc; has rpm equivalent to rpm of pad holder provided they are the same diameter
01-524-5653
Abrasive Wheel
Has common nylon threaded male (screw type) hub; easily mounts to either lockit or reloc holder pads with a half turn; stays securely in place for the life of the disc; has rpm equivalent to rpm of pad holder provided they are the same diameter
01-524-5654
Abrasive Wheel
Has common nylon threaded male (screw type) hub; easily mounts to either lockit or reloc holder pads with a half turn; stays securely in place for the life of the disc; has rpm equivalent to rpm of pad holder provided they are the same diameter
01-524-5655
Abrasive Wheel
Has all metal attachment on the holder pad
01-524-8921
Machine Hold Down Clamp
Used on apl update. 3 medallion jig jig that attaches to any xenetech vise with a set of dowel pins; one side of each bar consists of layered rectangular sides for clamping objects with flats; reverse the bars for insets designed for holding seals
01-525-2114
Chuck Universal Jaw Jaw Set
Used on duro-200/3 lathe chuck. soft top jaws
01-525-2653
Independent Jaw Chuck
Lathe chuck end item is a lathe machine
01-525-3356
Expansion Mandrel
Used on engine, acft, turboshaft, T700-ge models
01-525-3357
Expansion Mandrel
Used on engine, acft, turboshaft, T700-ge models
01-526-1453
Machine Hold Down Clamp
Used on tactical water purification sys; twps 4610-01-488-9656. clamps horizontal
01-526-1542
Machine Table Vise
Vise, speed used on engraving machine mdl 1313-250c
01-526-9274
Tube Bending Mandrel
01-526-9276
Tube Bending Mandrel
01-526-9277
Tube Bending Mandrel
01-526-9278
Tube Bending Mandrel
01-526-9279
Tube Bending Mandrel
01-526-9281
Tube Bending Mandrel
01-526-9282
Tube Bending Mandrel
01-526-9283
Tube Bending Mandrel
Hardened/ground finish is provided
01-526-9284
Tube Bending Mandrel
Hardened/ground finish is provided
01-526-9285
Tube Bending Mandrel
Hardened/ground finish is provided
01-526-9286
Tube Bending Mandrel
Hardened/ground finish is provided
01-526-9287
Tube Bending Mandrel
01-526-9288
Tube Bending Mandrel
01-526-9289
Tube Bending Mandrel
01-526-9290
Tube Bending Mandrel
Hardened/ground finish is provided
01-526-9291
Tube Bending Mandrel
01-526-9292
Tube Bending Mandrel
01-526-9293
Tube Bending Mandrel
Hardened/ground finish is provided
01-527-0227
Countersink Holder
Zephyr micro stop, c sink half inch f-16 am/bm aircraft end item
01-527-5403
Tube Bending Mandrel
01-527-5799
Expansion Mandrel Sleeve
2.000" overall length sleeve, flared od is 0.625; there is a flange on one end of sleeve, sleeve is split.
01-528-0563
Machine Collet
01-528-3146
Drill Holder
Accepts 0.031/0.125 in accessory shanks; quick change; use w/rotary tool dremel models: 275, 285, 398, 400, 750, 770, 780, 800; attachments: 212, 225, 575, 961; 3 jaw chuck
