00-762-8395
Counterbalance Weight
00-762-8710
Straight Shaft
11.880" overall length
00-762-8954
Shouldered Shaft
00-762-9101
Eye Nonrotating Shaft Bracket
12.000" overall length 6 bolt hole quantity two 31/64 in. dia holes one on each side of base, 2-1/2 in. from first bolt hole: center to center distance between bolt holes
00-762-9107
Bell Crank
0.874" bore diameter paint surface treated clevis ends
00-762-9152
Multiple Gears Gearshaft
First gear 0.642 od, 0.625 pitch dia; second gear 0.340 od, 0.320 pitch dia
00-762-9377
Rigid Connecting Link
00-763-0835
Retaining Shaft Plate
2.000" outside diameter finish is plating, cadmium class 3, type ii spec qq-p-416; mtg hole spacing: 4 holes spaced equally around a bolt hole dia. of 2.000 in.
00-763-1110
Remote Control Lever
0.435" bore diameter offset height: 0.188 in. offset, clevis link end
00-763-1111
Eye Nonrotating Shaft Bracket
0.770" overall length 1 bolt hole quantity
00-763-1193
Control Cam
Steel; one cam lobe; passivated per mil-std-171
00-763-1775
Shouldered Shaft
00-763-2201
Straight Shaft
1.781" overall length
00-763-2351
Spur Gearshaft
0.242" overall length
00-763-2787
Shaft Collar
0.688" outside diameter 0.3750" bore diameter pilot hole for 0.109 no. 4/0 taper pin oxide surface treated plain round
00-763-2999
Manual Control Lever
Material:steel, casting, composition 1c-303, solution heat treated, spec mil-s-81591; shaft end radius 0.437 in; length 1.718 in; setscrew 0.112-48 unf-2b; shaft end thickness 0.375 in; link endthickness 0.625 in; shaft hole dia 0.1875 in; finish:5.5.1, finish 24.17 of milstd-171; white no. 27875 of fed-std-595
00-763-4206
Counterbalance Weight
Used on engine j-85. steel aisi 316l, 0.350 in. o/a lg, 0.100 in. o/a w, 0.140 in. o/a h
00-763-4207
Counterbalance Weight
Used on engine j-85. steel aisi 316l, 0.295 in.o/a lg, 0.100 in. o/a w, 0.132 in. o/a h
00-763-4685
Eye Nonrotating Shaft Bracket
00-763-4832
Rigid Connecting Link
1.925" overall length
00-763-4853
Shaft Collar
0.713" outside diameter 0.3160" bore diameter chromate surface treated round stepped
00-763-5203
Eye Nonrotating Shaft Bracket
3.126" overall length 1 bolt hole quantity bracket has a socket on one end 0.624 inch dia by 0.6875 inch deep
00-763-5344
Remote Control Lever
Clevis link end, securing hole (s) shaft end
00-763-6343
Drive Flexible Shaft
7.560" overall length 0.130" outside diameter
00-763-6982
Shouldered Shaft
3.828" overall length
00-763-7525
Counterbalance Weight
Steel, qq-s-763, CL303, condition a, cold finish; finish 5.4.1
00-763-9085
Rigid Connecting Link
4.871" overall length cadmium surface treated
00-764-0318
Rigid Connecting Link
24.328" overall length
00-764-0654
Worm Shaft
2.812" overall length
00-764-1396
Rigid Connecting Link
7.243" overall length
00-764-1397
Rigid Connecting Link
18.290" overall length
00-764-1537
Control Cam
Used on 40mm m42a1. c/o cam p/n 764538; stud p/n 758345; shaft p/n 758635; pin p/n 544174; nut p/n 503566; 3 screws p/n 420555
00-764-1553
Shouldered Shaft
Used on goes on system local control,anti-aircraft m16a1e1. 10.320" overall length
00-764-1749
Shouldered Shaft
1.956" overall length
00-764-1901
Spur Gearshaft
00-764-1963
Spur Gearshaft
00-764-2466
Rigid Connecting Link
3.250" overall length
00-764-3424
Spur Gearshaft
1.046" overall length
00-764-3512
Shouldered Shaft
Used on 129007665876. plate material:brass, comp 1, tempered 1/2 h, spec qq-b-613; solder, brazing, comp b, spec qq-s-551; outside shaft: corrosion resisting steel, class 7, typea; inside shaft material: braze, class o, spec qq-s-561; heat treatment
00-764-3721
Rigid Connecting Link
13.718" overall length
00-764-3976
Spur Gearshaft
Spline data, involute 23 splines, 30 deg pressure angle
00-764-3977
Bevel Gearshaft
00-764-4036
Bevel Gearshaft
Material, steel, AMS6232, gear data, 48 teeth, 20 deg pressure angle, spline data, quantity two, involute, 84 splines, 30 deg pressure angle, 96 splines, 30 deg pressure angle
00-764-4441
Helical Gearshaft
Used on goes on computing sight m38. material:phosper bronze, comp temper hard; eighty teeth, 64 normal diametrial pitch, 1.251 p. diam. 14 1/2 degree std. involute, 1 degree 47 min. helix angle, rh. error in angular spacing between any two teeth not to exceed 2 minutes of arc. outside diam. 1.282; keyway width 0.188
00-764-4469
Shouldered Shaft
Used on 2350-00-049-4791. 4.170" overall length first end has hole 0.125 in.dia; second end has hole 0.094 in.dia
00-764-4715
Shouldered Shaft
1.562" overall length
00-764-5087
Manual Control Lever
Bronze manganese, qq-l-225, comp 2, or qq-b-726, class b, 1/2h. dimensions, 2.688 in. o/a lg, 0.432 in. fulcrum end thickness, 0.875 in. fulcrum od, 0.250 in. arm thickness, 2.250 in. distance from fulcrum hole center to arm end, 30 deg arm offset angle, 0.250 in. arm offset distance, 0.469 in. serrated fulcrum hole with thirty-six 90 deg serrations.
00-764-5092
Worm Shaft
Used on howitzer,105mm,m101/m101a1.
00-764-5381
Shouldered Shaft
8.563" overall length
