01-508-8783
Transmission Sleeve
01-508-8848
Caliper Disc Brake Parts Kit
01-508-8849
Caliper Disc Brake Parts Kit
01-508-9137
Transmission Sleeve
01-508-9140
Transmission Sleeve
01-508-9141
Transmission Sleeve
01-508-9142
Shouldered Shaft
01-508-9143
Shouldered Shaft
01-508-9144
Eye Rotating Shaft Bracket
01-508-9164
Rigid Connecting Link
01-508-9535
Eye Rotating Shaft Bracket
01-508-9802
Rigid Connecting Link
Used on overspeed governor. 15.500" overall length lever four holes drilled in lever. end has one hole drilled 21/32", other end has hole drilled .750-, .751+ diameter
01-508-9939
Shouldered Shaft
Used on diesel engine. shaft, water pump
01-509-0286
Ball Joint
Used on nha 6390668-02. ball end quality assurance tested
01-509-0411
Eye Nonrotating Shaft Bracket
01-509-0456
Straight Shaft
3.250" overall length shaft, idler dimensions in" 3.250 w, 2.375 h
01-509-0529
Control Cable Assembly
Cable assembly cable assembly-a/trans range sel lvr
01-509-0578
Actuating Line Cylinder Assembly
8.000" overall width 3.000" bore diameter hydraulic cylinder mounting provisions are pins; to order cylinder only for this assembly, order nsn 3040-00-762-2443; mounting type & location is tongue cylinder head end & tongue piston rod end
01-509-0584
Actuating Line Cylinder Assembly
Cylinder assembly
01-509-0776
Rigid Connecting Link
Used on overspeed governor. lever lever is used to hold adjusting nut/bolt to actuate push roller of limit switch. used on overspeed governor p/n 321668-9.
01-509-0872
Straight Shaft
16.675" overall length shaft, rocker lever dimensions in" 0.75 w, 0.75 h
01-509-1010
Straight Shaft
Used on overspeed governor. shaft used on overspeed governor p/n 321668-9
01-509-1071
Linear Actuating Cylin Parts Kit
Used on scraper tractor.
01-509-1073
Linear Actuating Cylin Parts Kit
Used on scraper tractor.
01-509-1087
Shouldered Shaft
01-509-1175
Eye Rotating Shaft Bracket
Used on engine, outboard, mercury 150cyl.
01-509-1184
Eye Rotating Shaft Bracket
Used on engine, outboard, mercury 150cyl.
01-509-1203
Extension Shaft
Countersink extension
01-509-1214
Mechanical Drive Housing
Engine heater housing
01-509-1219
Helical Gear And Shaft Assembly
9.000" overall length 7.000" overall width accessory drive
01-509-1434
Shouldered Shaft
Used on seawolf class ssn. 26.000" overall length shaft, actuator used on the ldt intermediate hatch assembly
01-509-1555
Electrical-fl Connector Assembly
01-509-1662
Straight Shaft
7.437" overall length shaft, accessory drive
01-509-1733
Mechanical Drive Housing
Used on engine, outboard, mercury 150cyl.
01-509-1734
Mechanical Drive Housing
Used on engine, outboard, mercury 150cyl.
01-509-1796
Shouldered Shaft
Used on mk32 mod2, slide, 5/62 caliber gun. 2.375" overall length shaft, locking
01-509-1824
Rigid Connecting Link
Used on yale hoist 5-ton. dr shft
01-509-1830
Shouldered Shaft
Used on yale hoist 5-ton. shaft de 15/06-061/11 shldr=1.574d
01-509-1908
Retaining Shaft Plate
Used on an/tps-73 antenna group base, matcals. 1.000" overall width adapter plate
01-509-2113
Rigid Connecting Link
Used on sikorsky agusta sh-sd helicopter.
01-509-2354
Actuating Line Cylinder Assembly
01-509-2359
Actuating Line Cylinder Assembly
Used on boat harbor security 25 foot guardian 25hs0205. front mount hydraulic cylinder this assembly is comparable to HC5345 assembly, except the mounting plate is located differently,
01-509-2426
Eye Nonrotating Shaft Bracket
Used on mk16 mod9, stand assembly. 4.000" overall length pivot base
01-509-2618
Bevel Gear And Shaft Assembly
10.000" overall length gear & shaft, acc drive
01-509-2773
Body Hub
Used on nimitz class cvn. hub
01-509-2801
Straight Shaft Assembly
Used on seawolf class ssn. adjusting, screw shaft is for adjusting the length to the hatch mechanism arm; one end of shaft has lh threads,
01-509-2826
Shouldered Shaft
Used on pump centrifugal, egs95, shipboard use.
01-509-2827
Rigid Connecting Link
Used on mercury outboard marine engine. bottom yoke used on the swivel bracket
01-509-2914
Rigid Connecting Link
Used on mk69 & 70, mod2, drive, 5/62 gun. 1.812" overall length link, threaded one end is threaded at 0.250-28 unf-3a, the other end is special shaped with bore diameter at 0.250" phosphate surface treated
