Serving our customers with quality and safety first.
3a
RIGHT-Hand
0.453in. ⁓29/64"
3.443in. and 3.463in. ⁓3-15/32"
spline drive shear head
0.257in. ⁓17/64"
0.671in. and 0.703in.
0.106in. first hole and 0.111in. first hole
0.711in. and 0.717in.
F18 e/f
0.4375in. ⁓29/64"
3.000in.
20
125000 pounds per square inch
3.328in. first hole and 3.338in. first hole
BOLT-Close tolerance, spline drive cres (125 ksi fsu) drilled, short thread
steel comp XM-13
ams 5629 assn std single material response
passivate
QQ-P-35 fed spec single treatment response
unjf
Unjf
Steel comp xm-13
20
3.000 inches
Spline drive shear head
0.453 inches
Right-hand
3a
Schedule B number: 7318152000
nmfc 093486
Bolts and bolts and their nuts or washers exported in the same shipment
FSC 5306 ⁓ Bolts
Used on f18 e/f. unjf thread series passivate surface treated bolt-close tolerance, spline drive cres (125 ksi fsu) drilled, short thread 20 thread quantity per inch 3.000" grip length spline drive shear head head style 0.453" thread length right-hand 3a thread class
1. | AIC687-7D48 | Cage 06725 |
2. | VS3174-7D48 | Cage 06950 |
3. | ST3M744-7D48 | Cage 0ZC92 |
4. | ST3M744-7D48 | Cage 58998 |
5. | 122895-7D48 | Cage 80539 |
6. | ST3M744-7D48 | Cage 76301 |
7. | 122895-7D48 | Cage 0PTK6 |
8. | VS3174-7D48 | Cage 17446 |
9. | SLB748-7D48 | Cage 16258 |
10. | GS1015-7D48 | Cage 1EM77 |
11. | PBF1265-7D48 | Cage 27624 |
12. | 122895-7D48 | Cage 56878 |
13. | 11823-7D48 | Cage 59563 |
14. | VS3174-7D48 | Cage 92215 |
15. | ST3M744-7D48 | Cage 1VSL7 |
16. | WC744-7D48 | Cage 60516 |
Nothing similar to this part number was found in our inventory
An externally threaded fastener whose unthreaded portion is of a specified grip length, plated or unplated, and is machined to a tolerance of one thousandth (0.001) of an inch (0.025 mm) or less of a specific diameter for items one inch (25 mm) or less in diameter. items over one inch (25 mm) in diameter shall have a tolerance of fifteen ten-thousandths (0.0015) of an inch (0.038 mm) or less. the nominal major diameter of the threads shall be at least one thousandth (0.001) of an inch (0.025 mm) below the minimum shank diameter, but not below the minimum major diameter for applicable class of fit, as shown in the screw thread standards, fed std h28 and/or other nationally recognized standards. the head is not designed to be held or driven with an inserted driver, nor is it designed for rotation by the thumb and fingers. a locking feature may be incorporated in the design of the head or threads. for items having close tolerance, and fabricated from material having 160,000 pounds per square inch (1100 megapascals) minimum tensile strength, see bolt, shear. for items fabricated from material having less than 160,000 pounds per square inch (1100 megapascals) minimum tensile strength and not having a close tolerance, see bolt, machine.