2.250 in. lg; 1.750 in. w; 0.870 in. h; two 0.172 in. dia holes 1.870 in. apart; rated 24.0 to 140.0vac; 3.0 amp; 47.0 to 65.0 hz; 4 thd stud terminals
ghermetically sealed; 1.810 in. max lg; 1.660 in. max w; 1.340 in. max h; one 0.350 in. hole 0.125 in. dp; input 28.0 vdc; output 20.0 ma; time delay 30.0 sec; 4 male quick disconnect solder terminals
Used on salinity indicator system ic/sb digital. 3.000 in. lg; 1.000 in. h; 5.000 in. h; three 6-32nc studs; one 4-40nc stud; 1 connector; output 50.0v at 40.0 ma
Used on armament subsystem,m28a1e2. c/O1-brkt plate .020 x 2.0 x 2.6, matl al aly, mtg plate .063 x 2.0 x 2.0wiring assy, resistor, 4-terminal, 2-diode, 2-insul tubing
spstno; input, 16 ma max at 5 vdc; output, 5 amp max at 120 vac; output freq, 20 to 500 hz; quick disconnect terminals; 1.400 in. lg; 0.800 in. w; 0.762 in. h
max load is 10 amps at 200 to 280 vac; control signal is 3 to 32 vdc; 2.250 in. lg; 1.750 in. w; 0.870 in. h; mounted by two 0.172 in. dia mtg holes spaced 1.870 in. c to c
dsolid state optically isolated, 5 or 10 amps, 140 or 250 vac, single pole single throw, normally open relay; input data: 90 to 250 vac voltage range, 47 to 70 hz; turn-on voltage: 90 volts rms min; turn-off voltage: 4 volts rms max; output data: 250 v rms output voltage; power dissipation: 0.85 w perampere; oprt temp -30 deg c to +80 deg c; 2.000 in. lg, 1.000 in. w, 0.900 in. h; environmental data; shock, 50g, 11 milliseconds; vibration: 20 g, 10 to 2000 hz
external dimensions length 2.000 in., width 1.000 in., thickness 0.900 in., single pole single throw, normally open relay, input voltage 3 to 8 vdc, rated turn-on voltage 5 vdc rated, 3 vdc min, rated turn-off voltage 0.6 vdc max, input current 0.008 amp max, turn-on time 0.006 sec max at at 400 hz, turn-off time 0.005 sec max at 400 hz, rated output voltage 250 vac, operating temp minus 30.0 deg cent to plus 80.0 deg cent
mspstno; input voltage range 10.0 vdc to 32.0 vdc; output voltage 50.0 vdc; weight 4.0 oz max; four disconnect terminals; 2.800 in. lg; 1.750 in. w; 1.270 in. h; two 0.170 in. dia mtg holes spaced 1.870 in. c to c
input voltage range is 95 to 132 vac; max output voltage rating is 18 vdc; optically isolated; built in snubber network; led status indicator; input terminals are screw
spstno; control voltage range, 3 to 15 vdc; load current, 4 amps max; load voltage, 24 vac nom; optically isolated; pin terminals; terminal mtd; polarized; 1.200 in. lg; 1.000 in. w; 1.100 in. h
cspstno; line voltage is 200 to 280 vac; ac input; max load current is 2.5 amps; screw terminals; 2.250 in. lg; 1.750 in. w; 0.870 in. h; mounted by two 0.170 in. dia holes spaced 1.870 in. c to c
time delay: 0.05 to 3.00 seconds; tolerance plus or minus 10.0 percent max; input: operating voltage 120 volts; tolerance plus or minus 20.0 percent of voltage; line frequency 50/60 hertz; output: type solid state; form normally open series connection; rating: max 1.0 ampere steady state; 10.0 amperes inrush; min 5.0 milliamperes; voltage dpop: 2.5 volts typical at 1.0 amperes; protection transient; dielectric: 1500 volts rms min; dc units reverse polarity; mounting: surface mount with one no. 8 or no. 10 screw; terminations: 0.250 inch male fast-on terminals; dimensions: length 1.960" min
Used on polar consoles. xinternal 10 amp dpdt relay; temperature range, operating m 10 deg c to p 55 deg c; delay on operate, external, res input voltage, 24vdc; time range, 0.1 to 10 sec, polarity protection 2.406 in. lg; 1.781 in. w; 3.435 in. h; weight 6 oz
dpdt contact arrangement; contacts rated at 10.0 amperes at 120.0 vac; time delay adjustable from 0.6 to 60.0 seconds; has polarity protection; 1.2 megohm external resistor; input voltage at 120.0 vac; eight solder lug terminals; two mtg slots 2.500 in. c to c; mtg slot width is 0.158 in.; 2.900 in. lg; 1.531 in. max w; 1.406 in. max h
line voltage is 120 vac; 3 to 32 vdc input; 10 amp load; 2.25 in. lg; 1.75 in. w; 0.88 in. h; two 0.172 in. dia mtg holes spaced 1.87 in. c to c; screw terminals
zreed-triggered triac; spstno; potted case; 5 amps max switching at 120 vac 50 to 60 hz; coil voltage 5 vdc; continuous duty; screw terminals; 2.250 in. lg; 1.750 in. w; 0.875 in. h; two 0.187 in. dia mtg holes spaced 1.875 in. c to c
spstno; input, 3 to 32 vdc; output, 120 vac 50 to 60 hz; quick disconnect terminals; continuous duty; two 0.187 in. dia mtg holes spaced 2.250 in. c to c; 2.640 in. lg; 1.520 in. w; 1.650 in. h
input voltage of 3 to 18 vdc; zero voltage switching; optical isolation; polarity protected input; logic compatible; pin terminals; terminal mounted; 1.700 in. lg; 0.400 in. w; 1.230 in. h
photo-coupled; triac controllers; 3 to 32 vdc current limited control input; reverse polarity protected; 24 to 280 v rms operation; zero voltage turn on; 120 vac input voltage; 2.700 in. lg; 1.520 in. w; 1.650 in. h; two 0.190 in. dia mtg holes spaced 2.250 in. c to c
1.280 in. max lg; 0.410 in. max w; 0.500 in. max h; two 0.120 in. dia holes on flange 1.062 in. apart; 8 hook terminals; input 28.0vdc; continuous duty; 16.0sec time delay
output configuration is dpdt; input voltage is 20 to 30 vdc; continuous duty; hermetically sealed; adjustable time delay on operate of 1 to 10 seconds; pin terminals; 1.718 in. lg; 1.025 in. w; 1.280 in. h; mounted by 3 0.150 in. w slotted holes spaced on the corners of an isosceles triangle, base 0.625 in.; altitude 1.396 in. min
control voltage 3-32vdc input; 40 amp max load; 1500 ohms input impedance; line voltage 80 to 530 vac, 47 to 63 hz; operating temp rng M30 to 80 degrees c; 2.250 in. lg; 1.750 in. w; 0.870 in. h; 2 6-32 threaded studs for conrol circuit; 2 8-32 threaded studs for output; 2 0.170 in. dia mtg holes, 1.870 in. c to c along length
dpdt; 5 amps at 120 vac; 120 vac input voltage; 1.2 to 180 sec adjustable time delay on operate; built-in transient protection; reset during timing with no false output; open board construction for economy; 3.625 in. max lg; 2.125 in. max w; 1.688 in. max h; four 0.141 in. dia mtg holes spaced on 3.000 in. by 1.500 in. mtg centers
